To connect plumbing fixtures to the water supply network, a flexible water supply is used. It is in demand when connecting faucets, showers, toilets and other water intake points, and significantly simplifies the installation process. Flexible connections are also used when installing gas equipment. It differs from similar water devices in its manufacturing technology and special safety requirements.
Characteristics and types
The flexible hose for connecting plumbing is a hose of different lengths made of non-toxic synthetic rubber. Thanks to the elasticity and softness of the material, it easily takes the desired position and allows installation in hard to reach places. To protect the flexible hose, there is an upper reinforcing layer in the form of a braid, which is made from the following materials:
- Aluminum. Such models can withstand no more than +80 °C and retain functionality for 3 years. At high humidity Aluminum braiding is prone to rust.
- Stainless steel. Thanks to this reinforcing layer, the service life of the flexible water line is at least 10 years, and the maximum temperature of the transported medium is +95 °C.
- Nylon. This braid is used for the manufacture of reinforced models that can withstand temperatures up to +110 °C and are designed for intensive use for 15 years.
The fasteners used are nut-nut and nut-fitting pairs, which are made of brass or stainless steel. Devices with different permissible temperatures differ in the color of the braid. Blue ones are used for connecting to a pipeline with cold water, and red ones - with hot ones.
When choosing a water line, you need to pay attention to its elasticity, reliability of fasteners and purpose. It is also mandatory to have a certificate that prevents the rubber from releasing toxic components during operation.
Features of gas connections
When connected gas stoves, speakers and other types of equipment also use flexible hoses. Unlike models for water, they have yellow and are not tested for environmental safety. For fixation, end steel or aluminum reinforcement is used. Distinguish the following types accessories for connecting gas appliances:
- PVC hoses reinforced with polyester thread;
- made of synthetic rubber with stainless steel braid;
- bellows, made in the form of a corrugated stainless steel tube.
Santekhkomplekt holding offers engineering equipment, fittings, plumbing and devices for connecting it to communications. The range is represented by products and materials from well-known foreign and domestic manufacturers. Discounts apply for bulk purchases, and product quality is confirmed by standard certificates. For information support and assistance, each client is assigned a personal manager. The ability to arrange delivery within Moscow and to other regions of the Russian Federation allows you to quickly receive the purchased goods without unnecessary hassle.
Drainage is a drainage and drainage measure to remove excess groundwater.
If water does not leave the site for a long time, the soil becomes gleyed, if shrubs and trees quickly disappear (get wet), you need to urgently take action and drain the site.
Causes of soil waterlogging
There are several reasons for soil waterlogging:
- clay heavy soil structure with poor water permeability;
- aquifer in the form of gray-green and red-brown clays is located close to the surface;
- high groundwater table;
- technogenic factors (construction of roads, pipelines, various objects) that interfere with natural drainage;
- disruption of the water balance by the construction of irrigation systems;
- The landscape area is located in a lowland, ravine, or hollow. In this case, precipitation and the influx of water from higher places play a big role.
What are the consequences of excess moisture in the soil?
You can see the results of this phenomenon yourself - trees and shrubs die. Why is this happening?
- the oxygen content in the soil decreases and the carbon dioxide content increases, which leads to disruption of air exchange processes, water regime and nutritional regime in the soil;
- oxygen starvation of the root-forming layer occurs, which leads to the death of plant roots;
- the supply of macro and microelements by plants (nitrogen, phosphorus, potassium, etc.) is disrupted, because excess water washes out mobile forms of elements from the soil, and they become unavailable for absorption;
- intensive breakdown of proteins occurs and, accordingly, decay processes are activated.
Plants can tell you at what level groundwater lies
Take a close look at the flora of your area. The species inhabiting it will tell you at what depth the ground water layers are located:
- perched water - it is best to dig a reservoir in this place;
- at a depth of up to 0.5 m - marigold, horsetails, varieties of sedges grow - bladderwrack, holly, foxtail, Langsdorff's reed;
- at a depth of 0.5 m to 1 m - meadowsweet, canary grass, ;
- from 1 m to 1.5 m – favorable conditions for meadow fescue, bluegrass, mouse pea, china;
- from 1.5 m - wheatgrass, clover, wormwood, plantain.
What is important to know when planning site drainage
Each group of plants has its own moisture needs:
- at a groundwater depth of 0.5 to 1 m they can grow on raised beds vegetables and annual flowers;
- water depth up to 1.5 m is well tolerated vegetable crops, cereals, annuals and perennials (flowers), ornamental and fruit and berry bushes, trees on a dwarf rootstock;
- if the groundwater is more than 2 m deep, fruit trees can be grown;
- optimal depth of groundwater for agriculture– from 3.5 m.
Is site drainage necessary?
Write down your observations for at least some time. You yourself can understand how much drainage is needed.
Maybe it makes sense to simply redirect melt and sediment water along the bypass channel, rather than allowing it to flow through your site?
Perhaps it is necessary to design and equip a storm drain and improve the composition of the soil and this will be enough?
Or is it worth doing drainage system only for fruit and ornamental trees?
A specialist will give you the exact answer, and we strongly recommend calling him. But after reading this article, you will gain some awareness on this issue.
Upon completion of technological and production tasks related to the arrangement of the sewer system in apartment building, industrial building, as well as in private households, it is required to test the involved system using the forced flow method. This task is used to identify possible defects or improper installation of the entire involved sewerage part, and the test report for internal sewerage and drainage systems will be material evidence of the work on acceptance of the facility.
A visual inspection should be accompanied by inclusion in the test report of internal sewerage and drainage systems according to SNIP, which is currently represented by the current regulations of the “D” series appendix, which corresponds to SP 73.13330.2012 “Internal sanitary systems of a building”, recently a new one has been applied updated working edition according to SNiP 3.05.01-85.
After a couple of operational years, the sewer well begins to silt up. The problem is difficult to prevent, but it is easy to prevent a major disaster.
Owners of personal plots ask themselves the question: what to do if the sewer well silts up?
The main signs of siltation of a structure are its rapid filling after pumping and the appearance of unpleasant odor around the sewer. There are several solutions to this problem.
Depending on the degree of siltation, you can clean the sewer tank yourself or seek professional help.
At first glance, it may seem that cleaning the structure is quite easy. In fact, the process requires compliance with all safety rules. This is influenced by the durability of the structure and the quality of materials.
For prevention, the sewer well is cleaned 3 times a year.
Important nuances that must be observed if the sewer well is clogged:
- About 3 people should be involved in the cleaning work. You should not do the cleaning yourself.
- Deep containers are best left to specialists.
- It is forbidden for people with heart disease to clean the container.
Step-by-step instructions on how to clean a well
Let's look at the process in detail:
- You should make sure that there are no gases in the well. This is achieved with the help of a lit candle. If all is well, it should not go out.
- The person must be secured with an additional rope. Use a safety helmet and wear waders on your feet.
- Next, the volume of water is reduced and the walls of the well are carefully cleaned. Don't forget about seams and cracks. All dirt and debris are collected in a bucket.
- When there is no water left at the bottom, it begins to clean it of debris, silt and mucus.
- The bottom filter is cleaned and washed.
- After cleaning the structure, it is necessary to seal the seams and cracks with cement.
- For cleaning, you can use a pump that has sufficient power and is specifically designed for this job ().
Read more: Lining of sewer wells – important nuances and features
If the sewer well is slightly silted, you can clean it yourself. In case of serious contamination, it is better to call a team of professionals or special equipment.
We hope that the article was useful to you. We will be grateful if you share it on social networks.
Read also:
Polymer wells - advantages of use
Construction of a drainage well from concrete rings- all the nuances
Drainage well from a barrel and other improvised means with your own hands - how to make it?
In order for the sewage system in the house to function normally, it is necessary timely care behind the pit where the waste flows. However, even in case correct operation the hole may fill up too soon. Let's highlight several reasons why it fills up quickly cesspool and what should be done to avoid this.
Impaired functioning
In order for the sewer system to function properly, it must be provided with proper care. In this case, the most important thing is timely pumping of wastewater. It is usually carried out once a year, but with a smaller volume, it can happen more often if the septic tank is filled with waste. However, when several years pass, the period between pumping may decrease, and the pit will begin to fill quickly. As a result, it may be necessary additional measures to improve technical characteristics cesspool.
Such reasons causing deterioration in the performance of the pit may be:
- silted bottom;
- fat deposits on the walls of sewer pipes, making the soil so that it does not absorb water;
- high pit filling speed.
As a result, a lot of waste accumulates in the pit, and a terrible smell accumulates, spreading around even with the hatch closed (except for absolutely sealed containers), the pit fills up too quickly and it has to be pumped out more often.
Silted bottom
One of the most common reasons To quickly fill a hole is to silt its bottom. You can get rid of this as follows. Firstly, it is necessary to pump out all the wastewater in the pit - for this they call a sewage disposal truck. Everything that the machine has not pumped out, that is, small residual waste in the pit, needs to be filled in clean water so that they soften as much as possible and become liquid. After some time, special biological products are added to the pit, containing a large number of bacteria that can cope with sludge.Bacteria are also necessary to clean the walls of fat deposits accumulated on their surface. These biologically based drugs are quite effective because their components are microorganisms that feed on sediment from the cesspool. What is achieved after using these microorganisms?
- The amount of sewage in the cesspool is reduced.
- Solid waste liquefies.
- It stops coming from the pit bad smell.
- Internal elements such as sewer pipes are cleaned of grease deposits.
- The pit drainage functions as before again.
- For a long time, the cesspool will not silt, and fat deposits will not form in it.
- All waste components become passive and not dangerous to humans.
Biologically based drugs differ in their application options. Some of them are used to cleanse sewer systems, sewage collectors, they are capable of destroying fats and resulting odors. And others make it possible to speed up the process of decomposition of waste that ends up in the sewer - fruit peels, toilet paper and the like.
These products are often used for outdoor dry toilets. The waste contained in them, as well as sewage, is simply converted into compost, which can even be used to fertilize vegetable gardens. Therefore, if the pit has already silted up, microorganisms will help deal with this problem best.
How can you prevent siltation at the bottom of a cesspool? Ideally, it will not be possible to completely prevent anything that silts up from getting into the pit, but something can be done. So, you can put a mesh on the kitchen sink, which will prevent solid waste from getting into the sewer. It is enough to place a bucket in the toilet for toilet paper instead of throwing it down the toilet. Then fewer products will fall into the pit and silt it up.You can get rid of the rapid filling of the sewer by installing a second collector. It is done at a short distance from the first collector. Both containers are connected by a pipe installed at a slight angle, through which water flows. This design can provide a system with two levels of cleaning, as a result of which the sewer system will work much more efficiently.
Pay attention! The pit intended for collecting wastewater should be located at a distance of about 30 m from the main well, no less, as required by sanitary standards.
Freezing of drains
If in winter they begin to accumulate in the cesspool waste water It is likely that the waste began to freeze. Most often, ice is formed due to improperly performed work on the installation of sewer thermal insulation, as well as poor quality installation work. However, even if all the work, including thermal insulation, was done correctly, the pit can still freeze.
A fairly effective way to defrost the contents of the pit is resistive heating of the conductors. You need to take a copper wire rated for 2 kW, a metal pin about 20 cm long, and a small hook. We must not forget that this method is best used by those who have at least a slight understanding of electrical engineering, since safety precautions are required here.
If the entire pit freezes, the following method must be used. A metal pin should be driven into the center of the frozen drains, connected to a wire, the end of which has been stripped. The other end of this wire, using a hook, is thrown over an element connected to the current, or a wire powered from the socket phase is used. A few hours, as with a pipe, cannot be done here - you will have to wait about a day or even two until the pit is completely defrosted. When the pit is frozen, the wire is de-energized and only after that is pulled out of the pit.
Pay attention! If during this process you have to be near the pit, then a prerequisite safe work There will be rubberized shoes and protective gloves.
In the case where only a metal pipe is frozen, it is necessary to warm up the sewer differently. You need to strip the wire enough so that you can wrap it around the frozen pipe once. The other end of the wire is connected to the phase in the socket. After just a few hours, the pipe will thaw due to the current passing through the metal pipe.
Another option for defrosting pipes is feeding inside the pipe hot water using a special device shown in the illustration.
For defrosting plastic pipes special devices are used, with the help of which a large current, about 400 A, is supplied through the ice in the pipe, as a result of which the ice quickly melts. As a rule, specialists are equipped with such equipment. The home craftsman can try using welding machine. The contacts should be in ice (in water) on opposite sides of the frozen pipe.
In the article, we examined the main reasons for the rapid filling of the cesspool, as well as winter problems that may give the impression that the pit is overfilled.
Video
This video will tell you about defrosting a water drain in a private house:
Owners of autonomous sewers often encounter problems that arise during the operation of treatment facilities. The most common among them is an unpleasant odor that spreads both throughout the entire territory and inside the house. What could be the reasons for the appearance of smell from a sewer well and how to get rid of it, we will consider in the article.
The smell from the sewer well is a problem whose solution should not be delayed. After all, it not only reduces the quality of life of the residents of the house, but also poses a health hazard.
To quickly and permanently get rid of the smell in a well, the first thing you need to do is find out the cause of its occurrence.
There may be several reasons that provoke the appearance of odor:
- installation errors treatment plant;
- malfunction of the water seal;
- incorrect operation of the ventilation system;
- death of beneficial bacteria in the septic tank.
It is not always possible to single out one main one among them. Only by checking several sources of unpleasant odor can you achieve the desired result.
Solutions to the problem
Incorrect installation Sewerage is perhaps the most serious and intractable problem. Typically, the cause of odor is stagnation of water. The sewerage drainage pipes must be located at a slope of 2 cm for each linear meter so that waste water moves freely through them at a speed of 0.8-1 m/second and flows freely into the septic tank by gravity. At the same time, exceeding a slope of more than 2 cm negatively affects the functioning of the system: the noise of the pipeline increases and its ability to clean itself decreases.
There should be no so-called “pits” or “houses” along the entire length of the pipeline.
Any kind of curvature leads to the formation of stagnant zones, which are responsible for the occurrence of unpleasant odors.
The second reason for this unpleasant phenomenon may be a loose pipe connection. In this regard, experts do not recommend connecting sewer pipes from various materials, since due to different coefficients of thermal expansion they will be destroyed during operation.
To eliminate the defect, you will have to perform a series of works:
- Dig a trench.
- Inspect the pipeline thoroughly.
- Replace seals.
- Caulk all connections.
Rubber rings D 50 mm and 110 mm are not difficult to find on sale. The tightness of the connections is increased by treating the ends with silicone-based lubricant. Silicone sealant can be coated with both polymer and cast iron pipes.
The easiest way to repair a crack or hole in a PVC pipe is to place a “sticker” on top of the defect. It is cut from a pipe of the same diameter. For fixation, use industrial-grade glue designed to work with polypropylene or polyvinyl chloride, or a solution of plastic in acetone prepared independently.
To eliminate the defect, disassembly will be required in any case; an attempt to cover up the joints from the outside is doomed to failure
Important! If the defective area is seriously damaged, it will have to be completely replaced. A temporary solution is to apply a rubber bandage from a bicycle inner tube, securing it with a binding wire or an aluminum clamp.
Well and pipeline cleaning
One of the reasons for the appearance of an unpleasant sewage odor may be the irregularity of maintenance of the treatment system. To clean sewer wells, they use sewage disposal equipment equipped with vacuum pumps and tanks with a capacity of 5-7 cubic meters to accumulate wastewater. Such machines are capable of pumping out any silt deposits from storage wells.
The hydrodynamic method is no less effective
Using a special device, water is supplied to the storage tank under high pressure. Mixing with sewage, it raises silt from the bottom of the well. The mixed waste can only be raised to the surface by pumping.
The most time-consuming but cheapest way is mechanical cleaning well. The work is done manually using a regular rope and bucket.
Mechanical cleaning allows you to eliminate all silt deposits that collect at the joints of elements
Access to sewer pipes is gained through inspection wells. The easiest way to clean the inner walls of pipes is hydrodynamic flushing. It is performed using mobile units to which hoses equipped with special nozzles are connected. Depending on the purpose, there are several types of nozzles:
- punching – for cleaning plugs and old deposits in the external sewer pipeline;
- rotary – to eliminate fatty deposits in pipes;
- bottom - for removing silt deposits and sand in storm drains.
When performing hydrodynamic flushing, on average, up to 25 liters of water are consumed per meter of sewer pipeline
To carry out hydrodynamic flushing, the end of the hose equipped with a nozzle is inserted into the pipeline and pushed towards the waste stream. Water supplied under pressure easily breaks down all deposits on the inner walls of the pipes. As noted by consumers who have already tried the hydrodynamic flushing method for cleaning sewer pipes, such a pipeline is subsequently less susceptible to contamination. This is explained by the fact that a thoroughly cleaned pipeline, like new pipes, acquires the ability to self-clean.
Arrangement of a water seal
There are often situations when sewer smell begins to appear in the house. And the reason for this is a malfunction of the water seal. It is a device in the form of a liquid-filled curved pipe that separates gaseous media without allowing them to mix.
The main task of the water seal is to prevent the spread of odor in the house
The malfunction of this device may be due to two reasons:
- When air pressure in the sewer pipe is higher than atmospheric pressure, which is present in the bathroom. At the same time, air noise is heard in the water, and splashes and bubbles are also observed.
- When the drained water fills the pipe cavity 100%. As a result, rarefied air appears, which “sucks” water from the water seal, opening direct access to gases from the sewer into the house.
Such situations may arise as a result of blockage in the system. Dirt deposits on the inner walls of pipes narrow the bore diameter, causing stagnation of liquid and, as a result, the spread of an unpleasant odor.
You can clear the blockage using irreplaceable assistant– plunger
Cleaning the system using chemicals. For this purpose, you can use ready-made formulations. They are sold in the form of powders and liquid solutions. In the absence of the opportunity to purchase special preparations, you can use improvised means: soda and vinegar.
If these remedies do not help, more radical measures will have to be taken. Cleaning sewer pipes can be done using a plumbing cable. A steel cable equipped with a rotating handle is inserted into the pipe cavity and breaks up dirt plugs.
If an unpleasant odor appears only when water is being discharged, this indicates that when installing the system, pipes of a smaller diameter were laid than required by regulations. The situation can be corrected only by replacing and installing pipes of equal cross-section with a diameter of at least 100 mm along the entire length of the sewer pipeline.
Setting up a ventilation system
Not all houses have full-fledged drains equipped with a well-thought-out ventilation system. Ideally, ventilation should be located as close as possible to the plumbing unit. Since all installations into which water and sewerage are supplied suffer from excess humidity.
Most often, when installing autonomous sewers, the role of ventilation is played by check valves and water seal units. They are able to cope with the task only if they prevent the septic tank from overflowing. As soon as the mouth sewer pipe for some reason goes under the water, the air in the pipes along with the drains begins to flow back into the bathroom or toilet.
If the ventilation is not working well, a musty smell in the area of the storage tank is guaranteed
The problem can be solved by installing a ventilation pipe in the septic tank. It is constructed from a cut PVC pipes D 100 mm. The structure is placed at an angle of 90° relative to the ground so that harmful gases freely leave the septic tank cavity.
When using treatment plants equipped with aerators, the cause of the odor may be improper adjustment of the oxygen supply to the storage tank. In this situation, you need to check the operation of the compressor and, following the instructions, adjust the air supply.
Video guide for installing a sewer pipe:
If ventilation is already provided in the house, but a foul odor still lingers in the space, you need to check the natural draft. To do this, you need to attach a piece of paper to the end of the pipe: if there is traction, the sheet will begin to flutter. Weak draft may indicate a blockage ventilation system. The easiest way to clean it is with a vacuum cleaner, inserting the hose into vent and running up and down along the inner walls of the channel.
Often the source of the unpleasant odor is mold, which forms colonies on the outer walls of ventilation pipes. The easiest way to “end” this is by arranging forced ventilation. To do this, it is enough to install a low-power fan in the exhaust duct.
Introducing beneficial bacteria
Ventilation in a septic tank is necessary for the bacteria living in it that process organic waste, so that they do not suffocate in their “production places.” If this happens and the colonies of bacteria die en masse, then an unpleasant smell of “fungus” will certainly appear in the area.
Several reasons can provoke the death of working bacteria:
- if drainage wells cannot cope with the water entering the septic tank;
- when there is no access fresh air into a storage tank;
- when the ambient temperature drops and the soil freezes;
- if there are chemical compounds in the effluent.
Bacteria are living things and they also need food.
For this reason, sewer wells and drainage pipes must be located below the freezing level of the soil. For different regions this parameter can vary from 80 to 180 cm. Working bacteria feel comfortable at temperatures of +4°C and above.
If the depth of the sewer pipe does not reach the freezing level, it is worth taking care of insulating the pipeline. Insulation based on fiberglass and polyethylene foam are ideal for this purpose.
The death of microorganisms can also be caused by the discharge of water containing a high concentration of detergents. Washing powders and soap compositions, when interacting with water, creating a large volume of foam in the storage tank, do not allow bacteria to function normally. A long break in the operation of a treatment plant can also lead to a disastrous result in the form of mass death of bacteria. The situation can only be saved by reintroducing a new portion of biomaterial into the sewer well.
Autonomous sewage systems can function effectively only thanks to bacteria. By taking care of these microorganisms, you can keep your entire treatment system running. And by using biological additives for preventive purposes, you will minimize the risk of failures.
Sewage wells are a means of draining wastewater from houses and their further disposal. Modern designs are made from the simplest elements, and other materials can withstand prolonged use.
But during use, a number of problems arise with this equipment. To eliminate them, you will have to clean and pump out accumulated waste and dirt using additional equipment. It is necessary to constantly monitor the condition of wells in order to eliminate them in a timely manner. emergency situations and unpleasant phenomena.
We list the main problems that arise during operation:
- Cluster large quantity drains.
- The appearance of silt at the bottom.
- An unpleasant odor characteristic of many wells.
The most common problem is water in the sewer well. It accumulates in case of clogging or the amount of incoming waste exceeds the capacity of the system.
If measures are not taken, the level in the well will continue to rise and the wastewater will come to the surface. An unpleasant odor appears that cannot be eliminated, and it spreads throughout the adjacent area.
To solve this problem you will need to run . There are three ways to do this:
- Vacuum.
- Hydrodynamic.
- Sludge sucker.
Vacuum pumping
Vacuum pumping is carried out using a tanker truck with a pump on board. A large diameter hose is lowered into the well and pumps water out of it. After collection, the tank transports the wastewater to the place of further discharge. This is the easiest cleaning method today; all liquid is removed from the area, and you do not have to worry about unpleasant odors.
Ilosos - solution to the problem
Sludge pump is another type of sewer truck. It is equipped with a high-power vacuum pump, the equipment is capable of removing not only water, but also various pollution from the bottom. The main advantage is higher efficiency and the ability to prevent future waste accumulation.
Hydraulic method
Most modern method- hydraulic engineering. Using a special device, pressure is injected into the well, it acts on organic and mechanical blockages, completely destroying them. The main advantage of the method is its high efficiency; the equipment not only pumps out water, but also eliminates the cause of its accumulation. The likelihood of the problem reoccurring after using the hydraulic method is extremely low.
To carry out water pumping and cleaning work, specialized equipment and extensive experience of specialists are required. Therefore, seek help from professionals.
Sludge accumulation at the bottom
Sludge accumulation is one of the main problems for all sewer wells. Sediment at the bottom of the well is formed from mechanical impurities in sewage, soil that can get inside, etc.
Sludge accumulates gradually; this process is almost impossible to prevent during the construction of the system and its operation. There are several signs that indicate the need for cleaning:
- The water drains slowly in the bathtub and toilet.
- A strong unpleasant odor appeared.
- Water accumulates in the well.
It is necessary to quickly solve this problem, otherwise it will become impossible to fully use the toilet and shower in the house. There will be an accumulation of a large amount of water in the well, with its further release to the surface.
If the sewer well has silted up, it should be urgently cleaned. Today there are two ways:
- Mechanical.
- Chemical.
Mechanical cleaning
Mechanical cleaning is a standard solution using a suction pump. This machine is equipped with a tank, pump, waste destruction equipment and other accessories, depending on the model.
Initially, specialists pump out most of the accumulated liquid and get to the silt deposits. They often acquire a hard structure and are difficult to remove immediately. Using a gun, the sludge is washed away and it is sucked out by a pump.
Chemical method
At chemically Most of the liquid is pumped out of the cavity. Special preparations based on nitrate oxidizing agents are introduced into the remaining water. They are completely safe to use and non-toxic.
The substances lead to the gradual destruction of mechanical deposits and their natural removal from the well. Note that the drugs will cost buyers a significant amount. Therefore, you will have to make a choice between relatively cheap and “dirty” mechanical cleaning, and expensive chemicals.
Smell
The sewer well contains wastewater containing organic waste. When decomposed, they release hydrogen sulfide, which has an unpleasant and characteristic odor. This is a completely natural process; it is almost impossible to completely get rid of this problem.
But if the smell from the sewer becomes increasingly stronger and spreads throughout the area, then there may be several reasons for this:
To eliminate odor, it is necessary to clean it every 1 to 2 years. Particular attention should be paid to the walls, rinse off silt and deposits. They are the ones that most often cause a strong and unpleasant odor from the well.
If the water level rises sharply, cleaning should be carried out as necessary. If there is no maintenance, it will be impossible to use the sewerage system, the drainage may flood the surrounding area, and a strong odor will appear in the area.
These are the main problems that arise during the operation of sewer wells. Carry out maintenance and cleaning in a timely manner, then the system will last for many years.