Hello, dear readers! Today we will talk about the correct installation on plastic windows roller blinds Modern systems, protecting the room from sun rays, are functional, elegant in appearance, easy to operate, and their mounting is so simple that even a housewife can handle it.
To install roller blinds we will need:
- roulette;
- pencil;
- building level and long wooden plank;
- hacksaw, scissors or stationery knife(if you need to cut the curtains to width).
If you decide to install a structure with drilling, additionally stock up on:
- electric drill with a 6 mm drill + dowels (for walls or ceilings) or 2.5 mm for wood (for a window system);
- Phillips screwdriver or screwdriver.
To install roller blinds without drilling, you need to additionally prepare:
- solvent for degreasing the surface;
- double sided tape(if it is not included);
- construction adhesive (for more reliable fixation of elements).
Preparatory stage
Before purchasing curtains, choose the principle of their installation. The canvas can completely cover the window opening - in this case, the structure is attached to the wall above the window or the ceiling. If the upper part of the frame is wide enough, you can install a roller blind on it, but in this case, with the curtains closed, it will not be possible to open the window for ventilation. There are also roller blinds that are mounted directly on the sash and do not interfere with opening the windows.
If you have chosen curtains attached to the sash, use a level to check the vertical installation of the window. On strictly vertical window systems, installation of roller blinds with a free edge is allowed - there will be no gaps between the canvas and the frame that allow light to pass through. In other cases, it is recommended to use roller blinds with curtain guides.
According to your choice, take measurements using a tape measure. If there are no curtains of a suitable width on sale, buy wider ones - the excess can be easily cut off. Use a hacksaw to trim the pipe on which the fabric is wound and the wooden bottom strip.
To calculate the length of the shaft when cutting a curtain, measure the required width of the curtain and subtract 8 mm from the resulting value (2x4 mm is the width of the two brackets). Cut the strip to the required width of the curtain. Applying the cut strip to the edge of the fully unfolded canvas, mark and cut with scissors or sharp knife excess material along the entire length.
The width of the curtain fabric for a sash with guides should correspond to the width of the double-glazed window, plus 3 cm. A curtain with a free edge is slightly wider, since it should overlap part of the frame. At the same time, it should not cling to the handle on the fold.
If you plan to attach a roller blind to the ceiling or wall above a window, first make sure that the finish will not be damaged when drilling the holes.
Drilling installation
Choose which side is more convenient to position the control chain, since the bracket for installing the control mechanism has a special configuration.
Then mark on the frame, wall, window opening or ceiling where the bracket for the control mechanism will be installed. In accordance with the marks, drill holes for its fasteners. Install the bracket without fully screwing in the screws.
To determine where to install the brackets on the wall or ceiling, determine the central axis of the window opening, set equal pieces to the right and left of it.
Insert a mechanism with a chain on one side and a plastic tip on the other into the ends of the shaft. Install the mechanism in the bracket and, using a building level and a wooden plank, level it horizontally, accurately determining the installation location of the second bracket.
Drill holes for the second bracket, secure both load-bearing element designs. Insert the shaft with the pre-fixed curtain into the brackets - first the end with the mechanism, then with the plug.
To secure the curtain to the shaft, you need to bend its top edge by 5 cm, forming a fold. The roller with the self-adhesive strip, from which the protective film has been removed, is installed in the fold with the adhesive part facing up, and then rolled towards the top edge. It is important that the canvas adheres strictly horizontally to the shaft.
Then roll the fabric almost completely and insert the bar into the special slot on the bottom edge. Correctly install the mechanism into the shaft - the canvas should be located close to the window.
Installation without drilling
The principle of assembling a roller blind and installing it remains the same. The difference concerns only the features of fastening the brackets - they can be glued to the sash or fixed on its upper edge using special hooks.
Fasteners with a hook are used if the sash with a seal has suitable thickness. In this case, the bracket is assembled from parts according to the manufacturer's instructions and installed on the upper edge of the open sash according to preliminary markings. Then the roller blind shaft is inserted into the brackets. Make sure that the door with hook brackets closes properly.
Brackets equipped with an adhesive layer are attached to the surface of the sash. To make the fixation as reliable as possible, be sure to degrease the installation site. Additionally, a suitable construction adhesive can be used.
The guides are also equipped with an adhesive layer - remove it protective film and attach the bar to the degreased surface, inserting the upper edge into the special groove in the bracket.
At the end of the installation of the roller blind, limiters are installed on the chain with which the curtain is raised and lowered - small plastic washers with a slot. The first stopper is installed on the chain when the bottom edge is raised to required height, the second - with the curtain completely lowered.
Video on the topic “how to attach roller blinds to plastic windows”:
Blinds have won respect for their simplicity and convenience. They are durable and can remain on windows for a long time without causing irritation to residents.
Blinds are a practical and convenient option for window decoration.
The variety of designs and color solutions on the product market is simply enormous.
How to hang roller blinds on plastic windows
But the price is not always affordable for the buyer. And sometimes you just want to see things around you that you created with your own hands. In both cases, the solution is this: make the blinds yourself. Moreover, it can turn out beautiful, unusual and inexpensive.
What materials and tools will be required?
Assembly diagram for vertical blinds.
To make blinds with your own hands, you will need a small set of tools and materials:
Where to start?
Scheme for attaching blinds to a window.
It will be easier to make vertical blinds, so let’s focus on describing their technology.
We select the roll of paper so that it is 2 cm narrower than the width of the window opening. We measure 3 cm from the bottom cut and bend the sheet. You have to fold a length of paper equal to the height of the window with an accordion. Place the accordion under a press for 2-3 hours.
Now you need to find the middle of the folded paper. You need to make through punctures in both directions from the middle at a distance of 3 cm. An awl is quite suitable for this purpose. The paper is attached to this rail with tape or simply glued.
How to assemble the structure?
Scheme of vertical blinds with an inclined system.
Vertical blinds are already ready, all you need to do is assemble them and correct location on the window.
First, glue the bottom of the folded paper in the center with tape. The thread is threaded through the hole from bottom to top, then turned around and threaded in the opposite direction. One end of the thread is equipped with a bead.
A movable clamp must be placed at the second end. Usually a clothes clip is used, but it will not look very nice. It is better to have complete symmetry, so it is recommended to drape these parts equally.
Here you can use various schemes drapery small parts(bells will look very nice and will hide the clips).
To prevent the thread from quickly wearing out when rubbing against a wooden slats, it is recommended to place a roller in the central part of the slats.
Now the vertical blinds should be placed on the window. Gravity will cause the paper to fall. This will be the extreme position for the stationary bead. The movable clamp is located at the same height.
We tie knots under the marked parts and cut off the ends of the thread.
How to test mobility
We fixed the clamp and obtained the required position.
The bottom edges of vertical blinds will sag. To eliminate this small flaw, you can equip the lower part of the blinds with a thin plate of any material, gluing it with double-sided tape.
For lovers of more refined interior elements, it is recommended to use your imagination. It will look very attractive if you bring both lower edges together and fasten them with glue or the same tape. The result will resemble a heart. Why not an option for lovers?
Where can you use homemade blinds and how to repair them?
Installation of vertical blinds.
It is clear that DIY blinds are made for use for a short period of time.
This is usually done before repairs begin. This way you can regulate the amount of light entering the apartment and save finishing materials from burnout.
Homemade blinds are suitable not only during renovations. They can be considered as great alternative factory products in country houses, garages and utility rooms. Homemade vertical blinds are used seasonally: in summer period they prevent light from entering the apartment, which helps escape the heat.
Repairing homemade vertical blinds is also easy.
It consists of replacing the paper (you will have to make a new accordion). When assembling a new product, the same procedure is followed.
Movement diagram of vertical blinds.
Do-it-yourself blinds do not have to be made from paper.
Home craftsmen advise using regular starched fabric for this. This makes sense: the material is thinner, and an accordion can be easily made using an iron. The fabric can be easily removed and washed, which makes vertical blinds more durable.
You can also experiment with bottom, giving the product completeness at your discretion.
But when using fabric for vertical blinds, you need to make the lower part of the product a little heavier. Typically, for this purpose, the bottom edge of the fabric is folded in half and stitched at a distance of about 5 mm from the bend. Subsequently, a metal (aluminum) wire is inserted into this hole. It will weigh down the blinds and keep their bottom edge in horizontal position.
This can be avoided if the edges of the holes are sealed with tape or treated with metal rivets with holes.
You can sew the holes with regular thread. The edges of the holes will be more durable, which will make vertical blinds handmade even more durable.
Repair of factory-made vertical blinds can be done according to the same rules as described for homemade ones. But replacing a certain part of such blinds will be visible even to the naked eye. It will not be possible to hide a defect, since it is very difficult to select a specific material color range. But there is no need to do this: it is enough to replace several elements at once during the repair.
It will turn out very beautiful and elegant. It will look as if blinds and curtains were specially combined.
Review How to assemble vertical blinds with your own hands.
Making a DIY blind roll is a task that every home owner can do.
Planar weighing scheme.
The lifting mechanism used in this embodiment is in the form of a shaft, raising or lowering the curtains due to its rotation.
DIY curtains like this - simple task, and it's fun to perform, you need to buy necessary materials and tools.
The use of roller structures with lifting mechanism in every room can transform it without recognizing it and can solve a wide range of design solutions.
But while installing curtains, you must consider all the shades as both of you can make the design look elegant and completely ruin the design idea.
Blinds or blinds are located directly on the frame or window, although they appear simple, they are no less interesting than expensive curtains or lambrequins.
Roller structures have a convenient lifting mechanism, so they have found their application in both offices and apartments.
Benefits of blinds
These elements are equipped with a convenient lifting mechanism; you can use them independently or together with other window design elements.
This design can be installed on plastic and wooden windows. Close the window and take care of them.
This design has a simple lifting mechanism, so it fails when using such curtains.
After correct installation they allow you to completely turn off the room, and there is a wide choice of colors.
Some people replace pilgrims and blinds.
They are similar in appearance, but Roman blinds consist of a cable system and the blinds have a lift mechanism that rotates and is located at the top of the structure.
Types and Types of Blinds
The shaft design can be open or closed, the electric motor can be used to control the shades easily.
Rolling structures can be with or without cassettes, lofts or blinds.
The control principle can be set manually using a chain or electric drive.
How to hang blinds on plastic and wooden windows by hand
There are such models, and for the material used there may be different types fabrics.
Characteristics of creating self-rolls
Let's look at an example of creating such a shape with your own hands, while the roll is at the bottom and the canvas is attached at the desired height using strips.
First measure the windows where this curtain is attached.
The width of the fabric should be 2-4 cm larger than the given size, and the length should be greater than 5-15 cm. Depending on which room you will install this design in, choose the fabric and pattern.
To work you will need:
- two pieces of fabric of the required size;
- ribbons to be used as covers should be twice as long as the curtains + 30 cm;
- a wooden bracket or hose for fastening, their width should be 1 cm less than the width of the curtain, you can buy a ready-made cassette system;
- stick or weight rod;
- screwdriver and screws;
- stapler;
- thread, needle.
Work order
Fold the two pieces of fabric on the wrong side and stitch on three sides, then wring out the bag.
Now you have to insert the weight, or you can make a special pocket for it.
The fabric is hungry and kept on a wooden stick, if a hose is used, the fabric hangs around it and the seams.
The posts fold in half and are also attached to the rod using clamps. After this, we fix the beam on the window frame.
Above we cannot do this work.
If you plan to remove the curtain, you can attach it to special hooks. To attach to a plastic window, you must use double-sided adhesive tape. Creating rolled structures is an exciting process, you don't need to have any specific knowledge or materials, so you'll end up with a beautiful window.
WINDOW MAINTENANCE
Place curtains on the window panes and it won't be as much. However, this requires specially designed curtains along with the appropriate accessories. Such curtains are attached directly to the sheet and rotate with it. They are equipped with a spring-loaded lifting mechanism and are secured in position by a locking hook.
Spring spring accessories are the flat part attached to the side of the frame.
Insert a wooden rod with a round cross section, which snaps into place with locking hooks attached to the sides of the frame.
Shimmering curtains of different tones and patterns are made in a special capacity for sleeping windows.
ROLE OF PROTECTION
BY WIDTH
When installing curtains in niche windows, they may need to be fixed to the width.
To do this, unscrew the fabric and cut off the metal shaft with the correct nut. Then draw a line with a pencil on the fabric that limits the desired width and cut it with scissors along that line. Replace the fabric on the shaft and install a narrow curtain.
COMPONENTS AND SPECIAL SIZE TYPES
The darker the curtains, the less light they transmit.
They are completely opaque among them.
Blinds on plastic windows
The fabrics of such curtains can be of different colors and with different patterns.
Curtains in a special design can reach a width of 300 cm and a height of 240 cm. Intermediate sizes are also possible.
Roller blinds can be equipped with lambrequins various shapes, such as the last elements of the curtain. Lambrequins come in a variety of colors and can be mistaken for tons of curtains.
The set of blinds includes supports with which they are attached to the wall, ceiling or side windows of the window niche.
The blind can be easily removed from the brackets for cleaning.
7 The range of colors and patterns of decorative fabrics for blinds is very diverse - you can choose a fabric to suit every taste.
2 If the edge of the curtain does not fit, you can decorate it with a cap. Here are lambrequins of three different shapes.
3 Universal plastic brackets that can be attached to vertical and horizontal surfaces.
4 Brackets for attaching rollers to plastic windows.
They are mounted on the frame and screwed in.
How to properly hang curtains on a plastic window
If you want to close the shutter window, you don't only need a curtain, but also go with guides. If you understand the installation nuances, install blinds on plastic windows without the help of experts.
Types of blinds
Drive systems are classified according to several parameters: type of design, steering mechanism and production material.
On the first sign, all curtain models are divided into two groups:
Open - the box does not close with the box, which makes the curtain less compressed against the glass, and the mechanism is not protected from external influences;
Closed - There is a safety cabinet which increases the cost of the system but provides better performance.
In addition, the system can have different geometric parameters: the shape of the guides, the diameter of the shaft, the width of the belt.
The choice of size depends on the surface of the hole, so you need to know how to measure a plastic window before ordering blinds.
To manage the system you can use the following mechanisms:
Plastic chain or chain, for example from blinds;
spring lock - automatically holds the blade when you unload it to the desired length;
electric drive - the shaft is equipped low-power electric motor, which can be remotely controlled.
Each option has its own purpose.
Thus, a spring is better suited if the curtains do not need to be adjusted frequently, but electric drive- if the system is unavailable. In most cases, twine is sufficient.
The blinds fabric is made from durable materials that do not stick to glass - polyester, cotton, nylon, coated bamboo and metal inserts.
They can provide different air permeability of the curtain; The following blinds are allocated with this feature:
Transparent - diffused sunlight used for decorative purposes;
smoke - partially passes through visible light, but blocks heat;
Fatigue - completely blocks light;
Day-Night - Alternating transparent and opaque sashes that allow you to let in and block light without collapsing the canvas.
Regardless of whether the canvas is made, it should be cleaned regularly soap solution, especially if there are curtains in the kitchen.
Curtain installation device
Before you decide how to hang your curtains, you must choose the type of balloon mounting.
The most popular method that is most suitable for large windows, is a wall or ceiling installation. The shaft must be screwed to the window opening, which creates many inconveniences - for example, a window with a curtain cannot open.
In addition, if this ends, it may get worse with such manipulations. In most cases, it is better to use a window aperture installation, since in this case the system can be mounted without drilling.
Next, you need to make sure that the window is completely vertical - you can use it flat or flat for this purpose. If there is deviation, the curtain will not fold properly and will not hold the glass well.
In this case, you must install it on a wall with a small recess from the frame or repair the window itself.
For a cylinder mounted on a wall or ceiling, add a hole 15 cm wide and 10 cm high;
When installing in a hole - remove N from the aperture width, measure the height as it is (N is equal to the size of the brackets depending on the system manufacturer).
The designated manufacturer may have their own design and measurement capabilities - this should be checked on the company website or in store.
Do-it-yourself prefabricated shutters on a plastic window
Once you've taken your measurements and purchased your system, you can figure out how to hang your blinds.
The easiest way to install them is with self-tapping screws. To do this you need to do the following:
1. Place the rails on the frame and tighten with the included fastener.
2. Insert the covers and gears into the shaft box or secure them to the shaft if the system is open.
3. Attach the shaft to the bracket by pinning it at the top and pressing it until it clicks into place.
4. Cover the edges of the box with decorative trim.
If you don't have a tool for tightening screws, you need to learn how to repair curtains without drilling.
To do this, you can use the Velcro that comes with the kit. Installation is performed as follows:
1. Velcro attachments are attached to the guides.
2. The window frame is degreased.
3. Velcro heats the hair dryer, then removes the protective film from it.
fourth
The system is assembled as described above.
Keep in mind that a curtain installed with Velcro will not hold as securely as one mounted with screws - the fasteners may need to be replaced for a while.
But if you need to remove the roller blinds, they can be easily soldered in this case.
Installation of rolls on plastic windows from A to Z
In the case of self-tapping screws, the system must be unscrewed. After this, the shaft is separated from the guides and the network is removed.
It's therefore very easy to install the curtains - just follow the instructions carefully. If everything is done correctly, there will be no problems with system performance.
← Austrian curtains in the Egyptian style interior →
The procedure for attaching roller blinds to windows
Instructions for use of horizontal blinds
Rules for using horizontal blinds.
1. The lamellas rotate around their axis by turning the control rod.
2. The lifting and lowering of the canvas is carried out by a control rope. To raise the blinds, pull the rope down. To fix the blinds at the desired height, move the rope away from the center of the canvas and release.
To lower the blinds, pull the control cord toward the center, thereby releasing the cord lock, and release the cord while holding it lightly.
Raising and lowering must be done with the slats in a horizontal position. The lower cornice can be fixed at any level.
3. Horizontal blinds Installed only indoors with relative air humidity up to 70%.
4. Avoid mechanical impact on the blinds.
The slats can easily become deformed.
5. Horizontal aluminum blinds do not require special care products. It will be enough to regularly wash them with a soft cloth or vacuum them with a brush with a soft attachment.
For washing it is recommended to use only cold or warm water(not boiling water or hot water!). If heavily soiled, the blinds can be removed and placed in a bath of warm soapy water. Be careful to leave the top cornice and control mechanism above the water. Rinse and dry the blinds thoroughly and let them air dry.
6. ATTENTION! Not allowed do-it-yourself repair products by the client.
Plastic windows have long ceased to be an attribute of office interiors. Today they are used both in old Khrushchev and Stalin buildings, and in modern new buildings. But so that such glazing does not introduce dissonance into the atmosphere home comfort, you need to be able to choose the right curtains for plastic windows that suit your living space.
Designers go to all kinds of tricks to make plastic windows look homely: they install the usual windows, add frames. But if the windows in your apartment still resemble office windows, curtains will help correct the situation. Ordinary floor-length curtains and tulle curtains on high cornices do not harmonize with such glazing. Needed here matching curtains for plastic windows that will not violate the laws of aesthetics.
To decorate your plastic windows according to last word in design, you should pay attention to the following types of curtains:
- Corrugated curtains– also known as “Pleated curtains”. The fabric with an antistatic coating gathers like an accordion when you need to roll up the curtain and let sunlight into the room. Depending on the design, the window can be opened slightly either from the bottom or from the top.
- Roman blinds- when unfolded, they are a straight piece of fabric, but when you need to open the window glass, starting from the bottom edge, they gather into beautiful horizontal deep folds. It is quite possible to sew such a design yourself with your own hands.
- Roller blinds– perfect for both living rooms, and for the kitchen or balcony. They are made of fabric and fastened with Velcro or brackets.
There are open and closed types of roller blinds. Open ones are fabric twisted into a dense roller, which is placed directly above the window. When closed and folded, they are hidden in a special cassette and are practically invisible.
Closed roller blinds for plastic windows (video)
Types of sun blinds on plastic windows
For owners of apartments whose windows face south, topical issue is the choice of curtains serving reliable protection from exposure to sunlight in the room on hot days summer days. Such products are subject to increased requirements.
Exists special kind roller blinds "blackout", which does not allow light to pass through
In particular, they should be:
- Made from high-quality fabric that will not fade in the sun;
- Reflect the sun's rays to protect the apartment not only from bright light, but also from the heat in hot weather.
For this purpose, those who prefer roller blinds need to choose a product made from heat-resistant and light-proof blackout material. This fabric ensures comfortable sleep even in white nights, as it is capable of blocking the sun's rays up to 100%.
A popular option for plastic windows are sun blinds with the “Day-Night” effect, also known as zebra. They are easy to recognize by distinctive feature- an unusual design in which transparent horizontal stripes alternate with opaque lamellas. Due to this, you can adjust the level of penetration of bright sunlight into the room, up to complete shading of the room.
Blinds are effective in combating the bright scorching sun. IN home interior Blinds with wooden slats or horizontal stripes of fabric will fit well.
Multi-textured blinds with vertical slats will give plastic windows an original appearance. Combinations of wood, fabric, plastic, and metal allow you to create unique compositions that will become a unique highlight of the interior. Such products are often complemented with lambrequins.
Features of fastening for curtains on plastic windows
Curtains for plastic windows do not have the usual hooks or loops, and they do not use eyelets. Therefore, such curtains cannot be hung on ordinary curtain rods or threaded through baguettes. To attach roller blinds or blinds, it will be necessary to mount the structure directly on the plastic profile.
There are different installation methods.
For curtains on the window fixation can be used:
- Latches;
- Self-tapping screws;
- Brackets;
- Liquid nails;
- Double sided tape.
Each method has both its tangible advantages and some disadvantages. Self-tapping screws and brackets, if used carelessly, will break the tightness of the plastic window, but they hold the heavy structure well. It is recommended to attach lightweight curtains with Velcro. Using liquid nails for installation will make it difficult to replace old curtains with new ones in the future. The latches are not suitable for all types of structures, but they cling directly to the window sash and are easy to replace open roller blinds with.
How to attach curtains to plastic windows with your own hands
The most popular type of fastening of common roller blinds, suitable for a plastic window, is fixing directly on the window. To avoid drilling unnecessary holes in the profile, it is recommended to use removable latches that can be attached directly to the sash.
For this:
- It is necessary to first degrease the junction of the plastic and the latch.
- Cut suitable size double-sided tape, which will securely fasten the latch and the window sash.
- On installed latches secure the movable shaft holders.
- Install a shaft with curtain fabric between them.
- Attach a spike with a gear for the chain mechanism to the shaft.
How to install roller blinds on a plastic window (video)
There is no need to doubt whether a plastic window will fit into your home interior. Modern market is filled with proposals that are designed to decorate this type of glazing in the best possible way both in residential high-rise buildings and country houses. And attaching curtains to a plastic window is not difficult if you know some of the subtleties of such installation.
Curtains for plastic windows (photo)
Roller blinds are gradually replacing curtains and heavy drapes from the market. This is due to their practicality and stylish design. Exists large number presented filters. They take up very little space and can complement almost any interior.
When purchasing roller blinds, users are interested in... This is a simple process that you can do yourself. There are several options for carrying out this process. The functionality and appearance of the curtains will depend on the type of installation chosen.
Design Features
Existing types of roller blinds for plastic windows have general design. The fabric is wound onto the shaft. Most often, dense cotton material is used for these purposes. There are a huge number of canvas design options. The bottom edge of the material has a weighting agent. It does not allow the fabric to deform during the process of winding and unwinding.
Today there are many design options for roller blinds on sale. They are divided into two large groups. The first category includes open-type roller blinds. The second group includes closed, or cassette and roller blinds for plastic windows.
Open roller blinds can be mounted above the window or in the opening itself. They, in turn, are also divided into several types. Closed structures have a special box into which the shaft and the material wound on it are placed. This type of roller blinds is most often used for plastic windows. However, they can also be installed on aluminum or wooden frames.
Open roller blinds
Before you know how to install roller blinds on plastic windows, it is necessary to consider their varieties. Open roller blinds can be fixed both above the window opening and directly inside it. This opens up many options for interior design.
If you need to install a separate light filter for each double-glazed window, mini blinds are used. They are selected according to the glass size of each window sash. If the curtain is mounted on the entire window, a type of “standard” roller blind should be installed above the window opening. If the windows have a complex configuration, “attic” curtains are suitable.
The curtain is controlled by a special chain or a spring mechanism. There are several options for attaching curtains to the window. The first involves using tape. In hot weather, the adhesive base may melt. The curtain may fall off. If the window sash is capable of opening, you can use special hooks. This option is not suitable for blind sashes. Installation of roller blinds on plastic windows with drilling holes and fastening with self-tapping screws is considered the best option.
Closed roller blinds
Today they are installed quite often. This is due to their aesthetic appearance. Previously it was believed that this type of roller blinds was suitable exclusively for plastic windows. Today they are used for frames made of any materials.
The system has a decorative box. It covers the shaft, giving the structure an aesthetic appearance. Systems vary in size. Small varieties are easy to install on a frame. They will not interfere with the opening and closing of the doors. However, large roller blinds require the installation of a durable shaft and a dimensional box.
Sometimes it is impossible to install such a structure above the opening. In this case, the system is installed directly on the ceiling. Guides are not used in this case. This may cause the canvas to deform in the future. Therefore, when choosing such types of roller blinds, it is necessary to take into account the dimensions of the space near the window.
Mini system
Studying how to attach roller blinds to plastic windows, it is necessary to consider the features of the main types of roller blinds. The “mini” type is distinguished by its compact shaft dimensions. They are installed on each sash. Installation in this case does not require drilling the frame. Anyone can handle this setup.
To prevent the filter material from sagging, the bottom guide is made of metal. Glued to the bottom frame magnetic holder. When opening the window for ventilation, the fabric will tightly cover the entire surface of the glass. In this case, sagging can be avoided. This is one of the most popular types of roller shutters.
These curtains cannot provide complete darkness in the room. There is still a small strip of light on the sides. If you want to completely prevent sunlight from entering the room, it is better to give preference to roller blinds that cover the entire window and part of the wall.
Window measurement for mini roller blinds
To correctly you need to study the methodology of how to measure roller blinds for plastic windows. There are several things to consider during this process. The fastenings of the mechanism should not interfere with the window when it is opened to its maximum. The window handle should not be an obstacle when lowering the fabric. The dimensions of the fabric material should be slightly larger than glass.
The measurement is carried out using a metal tape measure. You need to determine the length of the glass. Another 30 mm is added to the result obtained. This size allows you to completely cover the window sash with material.
Then the height is measured. To the result obtained you need to add 120 mm. This curtain length will be enough to completely cover the double-glazed window. The mechanism control must be located on the hinge side. The length of the chain should not be more than 2/3 of the window.
Measurement for roller blinds inside the opening
The installation option inside the opening in which it is installed requires particularly careful measurements. roller blinds for plastic windows. Instructions Taking measurements in this case will help you perform all the steps correctly. Every millimeter will have to be taken into account. Otherwise, the curtain simply will not fit into the window opening.
When taking measurements, you should take into account the unevenness of the walls. The dimensions of the opening are determined at three points. To carry out calculations, you must select the minimum value. This principle is applicable when measuring the length and height of an opening.
After taking measurements, you must subtract 1 cm from the minimum width result. The canvas with fastening should have this size. The fabric itself should be even smaller by 1.5 cm. The length is measured using a similar technology. Another 1 cm is subtracted from the result.
Measurement for installing roller blinds in front of the opening
Can be performed in front of the opening. In this case, it will be easier to choose the correct dimensions of the roller blind. In this case, the canvas can cover only the outline of the opening or a small part of the wall. This installation allows you to completely isolate the room from sunlight.
To choose the correct size of curtains, you need to measure the width of the opening and add 10 cm to it. Add another 15 cm to the length obtained. The height of the curtain should be measured from the attachment point to the plane of the window sill or even lower (if the design allows).
The mechanism control cord can be located on either side. For windows of non-standard shape, it is recommended to seek the help of a professional measurer. This will avoid mistakes.
Knowing how to attach roller blinds to plastic windows, it will be easier to choose the best option for roller blinds for a specific room. Experts recommend decorating deep, wide window openings with closed-type systems. They are mounted on the frame. In this case, the window sill can be used for decorative purposes.
If the window size is small, it is better to mount the roller blinds above the opening. This option is also preferable for a window with a small window sill. The cornice in this case can be quite long. It is better to choose the canvas in the color of the walls. This will visually increase the space of the room. Contrasting tones of the material are suitable for the “mini” variety.
If the canvas has a dense, loose structure, it is better to take brackets maximum length. They will be able to accommodate the entire canvas on the shaft. The mechanism should work quietly and smoothly. If you purchase a non-standard mechanism for moving the web (for example, the material moves in two directions), it is better to turn to professionals. In this case, the measurement will be as accurate as possible.
Installation of roller blinds
One of the most common systems is the Uni mechanism. To hang such curtains on the window, you need to unpack the kit. There are instructions here that allow you to familiarize yourself with the procedure, how to install roller blinds on plastic windows.
Use a pencil to mark the installation locations. The cornice is attached to the vertical sections of the frame using self-tapping screws. Protective covers are placed on the control mechanism. His work is being checked. The protective film is removed from the material. The upper edges are installed under the side covers of the mechanism. The guides are glued.
Having carefully studied how to attach roller blinds to plastic windows, everyone will be able to choose the optimal system option, as well as correctly install light filters.
Installing roller blinds with your own hands on PVC windows can be done quickly and with high quality, if you carefully fix the structure in accordance with the technology. Learn to install roller blinds using plastic windows is not at all difficult, just read this article to the end.
Roll cassettes for balconies
Installing roller blinds on a plastic window is an excellent way to save space in tight spaces. In addition, cassette rolls have grace, modern design(you can always choose the best option according to color scheme, texture and style),
Roller blinds are easy to install yourself
They are also distinguished by high functional qualities (they reliably protect the room from sunlight and dust, and prevent the rapid cooling of heated rooms).
The installation of roller blinds on balcony window coverings is carried out by specialized organizations that produce cassette blinds, but in order to save money, you can refuse the installation and do it yourself.
There are several ways to attach blinds to plastic windows; you will need to choose the most optimal option at the measurement stage before manufacturing the products: when installing in an opening; on the wall; on the sash.
Mounting methods
Roller blinds without drilling
Attaching a roller blind to a plastic window can be done in two ways:
- No drilling holes.
- Using the drilling method.
Before fixing the cornice, it is very important to decide how the window sill will be used. If you plan to fill it with pots indoor plants, installation can be carried out on remote brackets, which will allow not to obscure sunlight, which is necessary for photosynthesis of plants. In other cases, fastening the cornice of cassette rolls is provided for different designs: to the ceiling, walls, on the window sash or in the light opening.
Pre-drilling holes
Detailed instructions for installing roller blinds on windows with your own hands using drilling will help you quickly and efficiently fix the product. Let's consider the option of how to attach roller blinds to plastic windows yourself, carrying out preliminary work on drilling holes.
First you need to mark the mounting points
If the blinds are mounted on the shutters, then the top bar is mounted on window design using self-tapping screws. It is best to use self-tapping screws with a protective coating so that exposure to condensation does not provoke the development of corrosive processes.
To begin with, you need to mark the mounting points on the top of the glass unit; you can drill small holes. After that, the holes for attaching the brackets are aligned with the drilled holes and secured with self-tapping screws. To ensure reliable fastenings, screws must be screwed in using a screwdriver. After installing the brackets, you can install roller blinds on plastic windows (directly on the sash).
It is necessary to make two holes on the frame, which are made under the lower glazing beads of each sash. A fishing line will be threaded through the holes, which descends from the top bar. The lower holes for the fishing line must be drilled exactly under the exits in the top strip of the roller blind on the plastic window.
Plugs are attached to the lower ends of the fishing line, after which the fishing line is tensioned and the rolls are considered secured. Hanging roller blinds on plastic windows is not at all difficult; you just need to have some construction skills and special power tools.
Watch a video of how roller shutters are attached using drilling.
Installation of blinds without drilling structures
When installing rollers, it is not always necessary to pre-drill window fillings - a method for hanging cassette blinds without drilling will be described below.
Installation of roller blinds without drilling holes is used if the blinds are periodically removed for a long period of time (for example, removed from windows in winter period). In this case, holes from fasteners will be visible on the sashes for a long time, which will significantly reduce the decorative effect of the window and the entire interior. But how to hang roller blinds on plastic windows without deterioration appearance window opening?
Curtain fastening diagram
There are two ways to install roller blinds using gentle methods:
- The use of brackets that are attached to the upper part of the profile - this method has proven itself well when installing products on swing doors.
- The use of double-sided tape allows you to attach the bracket without disfiguring holes; the blinds can be easily removed for cleaning. Fasteners may become loose, especially when exposed to high or low temperatures, excessive humidity, or sunlight. The repair consists of replacing the tape (replacing a strip of adhesive tape). The method of fastening products with tape is indispensable for fixed and hinged doors.
Window curtains (roller blinds) cannot be attached to PVC windows at an angle; the geometric shape will visually change immediately, which will be noticeable and unsightly, so when drilling holes, accuracy is simply necessary. When attached with tape, an incorrectly installed piece can be easily removed and re-attached without disturbing the harmony and verticality of the blinds. The element to be fixed is immediately securely fixed in place; it is necessary to glue the bracket with careful and precise movements.
Features of installing rolls
It is best to place a roller blind on the window sash. This installation method does not prevent the window sashes from swinging open, without requiring the blinds to be moved or removed temporarily. Nothing interferes with the movement of the shutters, they open and close comfortably, the rollers do not interfere with movement, do not wrinkle or break. This is especially important when the blinds are made of brittle plastic.
Roller blinds are beautiful, practical and convenient
Ready-made blind kits come complete with mounting hardware and also include detailed instructions manufacturer according to optimal options securing products. It is necessary to follow the manufacturer’s recommendations without violating the blinds’ fastening technology, then the rollers will last a long time without the need for replacement.
You now know detailed instructions on how to hang roller blinds on balcony openings yourself. All you have to do is choose the blinds, the installation of the roller blinds will be done with high quality and compliance with the instructions.
- pencil;
- roulette;
- scissors;
- a screwdriver and a drill with a Ø 2 mm drill (for installation on double-sided tape, you do not need a drill and a drill).
Open the package and take out the MINI roller blind. Do not use a knife or blade to cut the packaging to avoid damaging the product!
Option No. 1 – how to attach roller blinds WITHOUT drilling – using double-sided tape
Place the roller blind on the window and use a pencil to make markings for gluing. To avoid uneven winding of the fabric on the shaft due to non-horizontal installation of the product, we recommend using a building level. Degrease the adhesive areas with the means available to you - apply alcohol, lighter gasoline or nail polish remover (containing solvent) to a cotton swab and wipe well. Remove the protective film from the tape on the top curtain rod of the roller blind. Pressing tightly, glue the entire structure to the window leaf. Please note that installation with double-sided tape is suitable for products standard size, but not recommended for large sizes products (due to their heavy weight).
Option No. 2 – how to attach MINI roller blinds to self-tapping screws
Place the roller blind on the window and mark with a pencil at the attachment points. To avoid uneven winding of the fabric on the shaft due to non-horizontal installation of the product, we recommend using a building level. Screw the top brackets to the plastic window frame using self-tapping screws. Snap the top curtain rod of the roller blind into the brackets until you hear a characteristic click.
Option No. 3 – how to install MINI roller blinds on hanging brackets
Insert the plastic hanging brackets into the grooves in the top cornice. Remove the protective tape from the hanging brackets. Degrease the gluing areas with any available means and remove the protective layer of tape from the hanging brackets. Place the entire structure onto the upper part of the window sash according to the markings and press tightly at the fastening points.