Help me fix this bug.
This is the first time I’ve done any repairs on my own, and this is the first time I’ve made such a mistake. It turned out that the new doors, which I bought for a lot of money, in general, do not fit the height of the doorway. I'm a little shocked and didn't even think it would happen like this. How can this be fixed?
doors for bathrooms and toilets: how to trim a door from the bottom
Is it possible to cut MDF doors?
Is it possible to cut the door from the bottom?
If the doors are not “paper”, plywood or Canadian type, then they can be cut a little to size so that they fit into the doorway, or the doorway itself can be enlarged. A the best method there will be a purchase new door, exactly the size of the doorway. If it is non-standard, order doors of the required size from a carpentry shop or workshop.
how to reduce the height of a door saw off a door
master class to shorten a door without chipping
Is it possible to saw off a door from the bottom cheaply?
how to cut a door with a jigsaw yourself
Your problem is not as bad as you think
Not only beginners, but sometimes even professionals in their field encounter it. If the door turns out to be larger than the doorway, then you just need to adjust the door to fit right size. To do this, the door just needs to be carefully trimmed. Just do this very carefully and carefully so as not to damage other elements of the door. Reduce the door little by little so that it does not become much smaller than the doorway.
trim interior doors, how to install a toilet door yourself
how to trim a box from the bottom
How to trim a laminated door?
I wonder how you are going to file doors that are covered with PVC film? Or laminated profile? And it’s even better if it’s the entrance metal door... It’s not so easy to deal with metal. You can do it differently. Go to the market where I sell doors and make an exchange deal. True, you will have to spend a little, since the seller needs some kind of benefit from this.
What is the best way to trim a door without damaging it?
It also seems to me that it’s better to just replace the doors if everything is so critical. If you bought a door for a lot of money, it will be a shame to ruin it by trying to fit it to the opening, if at all possible. In some cases, it is probably easier to fit the opening to the door, but the easiest thing is to hand over or exchange these doors.
How to trim doors, tell me how to trim doors evenly?
The bad thing is that the size of the discrepancy was not indicated, but nevertheless they gave sensible advice, I especially liked the idea that you could try to replace the door. It’s as if I hadn’t thought of this myself, I would have immediately started racking my brains about where and what to remove in order to fit the door, even to the point of widening the opening and installing a new door, if the jamb was decent, but go and try to exchange the door for God would never have thought of anything less... maybe no one would even want to, but it would certainly be worth trying to use such an attempt.
how to trim doors with glass insert
how to prune wooden door video
how to shorten it yourself interior door
I also believe that if you did not order a door to your size, that is, you bought a standard one, albeit an expensive one, then it can be returned to the store within two weeks or exchanged for another, according to the consumer rights law. If the discrepancy is small, then you can still try to fit the box under the door, I still wouldn’t touch the door.
how to trim a door without removing it from its hinges
how to trim a door to height along with the frame
After laying the laminate, the floor rose 2 cm, and one of the doors needed to be sawed down 1-1.5 cm from below.
Interior door, simple laminated, covered with MDF. Corrugated inside.
What could be used to file the door so that:
1) it was smooth
2) there were no chips or “brush” effect on the saw cut.
Cover the cut with masking tape.
Sawing with what? Drag it to any format. (saw for cutting sheet materials) Available in all large construction shopping centers and carpentry factories. Don't even try using a jigsaw or hacksaw. In theory, it can be cut off circular saw"frog", but you need very straight hands.
Do you have any similar experience? I just don’t think that the shopping center will be happy if I bring them a door and say that it would be necessary to cut it off by 1-1.5 cm. I didn’t cut it in the shopping center, but I sawed off a lot of doors at a friendly production facility.
I sawed with an electric jigsaw, having previously wrapped it in masking tape. It doesn’t turn out very nicely, but if you don’t crawl along the floor with a ruler, it won’t be noticeable. How much did you saw off? What's inside at this height?
This is if you cut along a line, and if you run a jigsaw along the guide, then the file will be thin and will lead vertically. I sawed 16 mm as hard as I tried, the line is straight, but the vertical is moving. But the idea with the router is the best idea of all.
Nope, it won't. There will be a “four” on plywood. At 40 mm door leaf- no. With a circular saw - most likely it will work. Along the guide bar.
At Stroy Arsenal, they will most likely undertake to cut it off, and the price tag will be ridiculous. I brought them 32mm chipboard to cut. They took it at the rate of 35 rubles. for the detail. They can take the same amount out the door.
Usually the canvas is no thicker than 40 mm. That's exactly what the guy who was installing another door said.
Yes, the blade is 40 mm. Just sawing the door is a responsible task :-D And the opening was foamed, covered with platbands and no jambs are visible.
If the block is 5 cm, but you need to saw off 2 cm, then there is no problem - use a jigsaw and go ahead (adhesive tape for the “beard”).
But if you are afraid that you need to saw off more than the width of the bar (you will hit the compartment with the corrugation), then it is better to take it to those who have special equipment!
Moreover, if you cut without a guide bar, the blade will move less vertically. Because it is possible to press the jigsaw slightly left and right and control the blade (do not unfold it, but press horizontally)
With a block, the canvas moves much more precisely, even to the point of breaking if you overdo it.
You've inflated the topic! Normally these doors can be sawed with a hacksaw. and.a jigsaw!!! :-D
After laying the laminate, the floor rose 2 cm, and one of the doors needed to be sawed down 1-1.5 cm from below.
Interior door, simple laminated, covered with MDF. Corrugated inside.
What could be used to file the door so that:
1) it was smooth
2) there were no chips or “brush” effect on the saw cut.
Cover the cut with masking tape.
Sawing with what? Drag it to any format. (saw for cutting sheet materials) Available in all large construction shopping centers and carpentry industries. Don't even try using a jigsaw or hacksaw. In theory, you can make a “frog” with a circular saw, but you need very straight hands.
Do you have any similar experience? I just don’t think that the shopping center will be happy if I bring them a door and say that it would be necessary to cut it off by 1-1.5 cm. I didn’t cut it in the shopping center, but I sawed off a lot of doors at a friendly production facility.
I sawed with an electric jigsaw, having previously wrapped it in masking tape. It doesn’t turn out very nicely, but if you don’t crawl along the floor with a ruler, it won’t be noticeable. How much did you saw off? What's inside at this height?
This is if you cut along a line, and if you run a jigsaw along the guide, then the file will be thin and will lead vertically. I sawed 16 mm as hard as I tried, the line is straight, but the vertical is moving. But the idea with the router is the best idea of all.
Nope, it won't. There will be a “four” on plywood. On a 40 mm door leaf - no. With a circular saw - most likely it will work. Along the guide bar.
At Stroy Arsenal, they will most likely undertake to cut it off, and the price tag will be ridiculous. I brought them 32mm chipboard to cut. They took it at the rate of 35 rubles. for the detail. They can take the same amount out the door.
Usually the canvas is no thicker than 40 mm. That's exactly what the guy who was installing another door said.
Yes, the blade is 40 mm. Just sawing the door is a responsible task :-D And the opening was foamed, covered with platbands and no jambs are visible.
If the block is 5 cm, but you need to saw off 2 cm, then there is no problem - use a jigsaw and go ahead (adhesive tape for the “beard”).
But if you are afraid that you need to saw off more than the width of the bar (you will hit the compartment with the corrugation), then it is better to take it to those who have special equipment!
Moreover, if you cut without a guide bar, the blade will move less vertically. Because it is possible to press the jigsaw slightly left and right and control the blade (do not unfold it, but press horizontally)
With a block, the canvas moves much more precisely, even to the point of breaking if you overdo it.
You've inflated the topic! Normally these doors can be sawed with a hacksaw. and.a jigsaw!!! :-D
How to trim a door video
It would seem, why cut an already installed and working door. However, sometimes such a need arises, for example, if the installation of interior doors has already been carried out earlier, and during the next renovation the owner needed to lay laminate flooring on the floor, but the height of the doors was not designed for this. In this case, it is much easier to shorten the door than to replace it with a new design. The question is how to do this correctly and competently.
Any homeowner, when producing, expects that the new design will serve him, as they say, faithfully, for many years. To do this, he chooses reliable and high-quality doors from trusted manufacturers or orders from professionals and wants to be sure that he will not need to repair interior doors. In most cases, this happens, however, there are situations when it is necessary to trim the door in height, for example, if during the next renovation the owner wanted to replace flooring, and he decided that laying laminate or parquet board would be a great option. As you know, laying parquet boards and laminate flooring involves changing the floor level, and, therefore, it is necessary to shorten the door so that it does not touch the flooring when closing and opening. After all, it is unlikely that anyone would think of purchasing and re-installing interior doors, which entails large expenditures.
And here comes the most difficult moment. Few non-professionals know how to properly trim a door to avoid possible damage and damage. appearance designs. Of course, ideally, you should contact specialists who install and repair interior doors and have the professional knowledge and tools to perform this, by no means simple, operation. But if this option does not suit the homeowner or is impossible for some reason, he can cut the interior door himself. And for this he will need either manual or hand router, available in the arsenal of most home craftsmen, as well as video instructions on exactly how to trim the door so as not to spoil it.
Using manual circular saw By the way, you can shorten an interior door without even removing it from its hinges. To do this, you must first carefully measure required size sawed, setting the circular saw blade in such a way that when passing along a flat surface of the floor and sawing the door, making an even horizontal cut across the entire width of the blade. You can visually see exactly how the door is trimmed without removing it in the first video instruction in this section. This operation is usually carried out before the laminate is laid on the floor, since otherwise it is much more difficult to trim the door without removing it from its hinges.
In this video you will see how to trim an interior door without removing it from its hinges
More complex, time-consuming, but also more convenient way shorten an interior door - use a hand router. In the second video you can see the whole process in detail. To do this, the door must be removed from its hinges, secured on a flat surface of a table or workbench using clamps, pressing them evenly on top wooden block, which will serve as a guide for the router. It is important to install it so that the cutter removes wood strictly at the distance required. With a router, trimming a door will take more time than with a circular saw, because you will have to make several passes, gradually going deeper into the canvas. However, this method of shortening the door is more reliable, especially if home handyman is not a specialist and