Thatched house. How to make an outdoor washbasin for a dacha with your own hands - various options Do-it-yourself cabinet for a dacha washbasin

Not everyone at their dacha has running water, but the need for water arises quite often: it is necessary to rinse your hands repeatedly after gardening work, to wash vegetables or fruits, or to wash dishes after eating. All this can be done using a washbasin. It comes in handy not only inside a country house where there is no running water, but also on the street, in the garden or next to the gazebo where there is dining table. The good thing about a portable washbasin is that it can be installed anywhere. There are several types of washbasins that differ in design: from the simplest to convenient units with a cabinet and heating. The latter are so convenient that they can partially replace a full-fledged plumbing system. Until recently, in order to make a washbasin for a summer house with a sink, you had to make many of the elements yourself. Now modern market can offer various ready-made options. However, let's remember how you can make a washbasin with your own hands. After all, a handmade item is not only unique, but may also have many elements or functions that you need, but they are not provided in ready-made models.

Types of washbasins for the garden

The main difference between all washbasins is functionality. To do right choice, you need to understand exactly what you want to see and how you are going to use it. Is a simple wall-hung washbasin enough for you or do you need a unit with a cabinet or even hot water?

Simple wall-hung washbasins for a summer residence

The simplest washbasin is a slightly barrel-shaped container with a press-on spout. The volume of such washbasins does not exceed 3 - 5 liters. Thanks to special fastening elements, such a washbasin can be hung anywhere where there is a suitable vertical surface. For example, on a fence, on a tree, on a board driven into the ground or other convenient surface.

You need to pour water into a simple washbasin manually. But drainage can be organized in different ways. A lot depends on where the sink hangs. For example, you can place a container under the washbasin into which waste water will be collected, and then, as the bucket is filled, take its contents into the compost pit. If the washbasin is used quite rarely, you can not place anything at all - let the water pour on the ground. And to make water seep through more easily, you can pour a layer of crushed stone or fine gravel under the washbasin.

Such simple washbasins are still popular, as they allow you to easily and quickly wash your hands after dirty work in the garden or garage. But due to its small volume, it is difficult to use for washing dishes after a family dinner.

Wall-mounted washbasins with a larger volume from 10 to 18 liters are more convenient due to the fact that they require less frequent filling of water. The shape of such washbasins can be different: rectangular, oval, slightly rounded. The material of manufacture is either plastic or stainless steel. As a rule, washbasins with a volume of more than 10 liters are equipped with a valve tap, which is located on the front wall. These taps are very convenient: turn off the valve and use water, turn it on and the water stops flowing. In models with a pressure spout, you need to constantly press it, which can sometimes be inconvenient or difficult.

Large wall-hung washbasins can be attached to vertical surface, for example, to the wall, or hang it on a cabinet. They are used both indoors and outdoors.

Enough unusual option outdoor washbasins - unit on a counter. The water container is fixed on top of the metal stand. You can install such a washbasin anywhere, including where there is no vertical support. At the bottom of the rack there is a crossbar, after pressing with your foot the horns - supports are firmly driven into the ground. Thus, the washbasin on the counter is quite firmly fixed in any part of the garden.

It can be used to wash your hands or face while working; just unscrew the valve and the water will flow by gravity. The capacity of countertop washbasins is usually from 8 to 15 liters.

You can make a similar counter for a washbasin yourself. Will be needed steel pipes, Bulgarian and welding machine. For greater stability of the racks - supports there should be at least two and the distance between them should be 20 - 25 cm.

We measure the required length of the supports and cut off two pipes.
In order for the posts to easily penetrate the ground, the end of the pipes from which they are made must be cut at an angle. Sharp end the posts easily pierce the ground.
We cut off the lower jumper and the upper bar to which the washbasin is attached.
We weld the jumper and the top bar to the supports.

Instead of pipes, you can use reinforcement or steel corners 25x25 mm.

Washbasin with cabinet for a summer residence - “moidodyr”

The Moydodyr washbasin is a structure consisting of a cabinet, a sink and a washbasin (filler tank). It is more functional, it can be installed both inside the house and outside. Despite the fact that a washbasin with a cabinet is heavier simple models, it can be dragged from place to place by two people. A bucket or other container for drainage is installed in the cabinet under the sink.

Thanks to the presence of a sink in a washbasin with a cabinet, you can not only wash your hands and face, but also conveniently wash dishes or fruits and vegetables. For example, a bowl of freshly picked strawberries can be placed inside the sink. The valve tap on the wash basin allows you to thoroughly wash the berries under running water.

As you can see in the photo showing a washbasin for a summer cottage, similar models of washbasins can be equipped with a mirror, a towel hook and a soap stand. You can store inside the cabinet detergents for dishes and washcloths.

If you are going to install a washbasin with a cabinet inside the house, then you can choose any model, including one with a wooden cabinet. On the street, wood, chipboard or plywood will quickly become unusable. For outdoor use, washbasins with a painted metal cabinet or a cabinet lined with polycarbonate are better suited.

The heated washbasin is a more advanced model of the washbasin with a cabinet. In fact, they differ from each other only in that a heating element is installed in the water tank, which heats the water. The sink and cabinet are exactly the same.

In early spring and autumn, the water in the washbasin is practically not heated by the sun. And if water from a well is used, then it is simply icy. The heated washbasin allows you to feel complete comfort. Wash warm water, wash dishes hot. All this is possible thanks to the thermostat. Using it you can set the required temperature from +30 to +70 °C.

A container with a volume of 10 to 20 liters is usually made of durable plastic, similar to that used in electric kettles. Sometimes heated models have a stainless steel body. Ready-made heated washbasins, which can be bought in stores, have standard sizes: width and depth of the cabinet 0.5 m, height of the cabinet 1.0 - 1.5 m.

Do-it-yourself washbasin for your dacha

The cost of washbasins is not that high. For example, prices for a washbasin with a cabinet and heating start from 85 USD. So if you have an extra hundred dollars, then there is no point in going to the trouble of constructing a washbasin with your own hands. But if you really want to do everything yourself, or you have a unique functional design in mind, then below we will give recommendations on how to make a washbasin for your dacha with your own hands.

Water container - which washbasin to choose

If you want to make a washbasin with a cabinet for your dacha, then it makes no sense to fool yourself and make a water container yourself. It is unreliable, unaesthetic and ineffective. For example, you can make a tank from an old 5 - 10 liter water bottle, but why? The cost of a washbasin with a valve tap does not exceed 10 USD, but it looks much more beautiful.

Container with water for a washbasin with a cabinet it should be from 10 to 20 liters. It makes no sense to take less.

Material of manufacture capacity also matters. Most often, washbasins are made of plastic and stainless steel. Which one to choose depends on personal preference, but there is an important caveat.

Important! A stainless steel washbasin for a summer residence is more preferable because it is more reliable and durable. If you accidentally drop a plastic sink filled with water, the chance of it bursting, cracking or splintering is much greater than if a stainless steel sink is dropped. We rarely think about such things, but when we encounter them with our own eyes, we regret wasting money.

Washbasin shape is also important. Usually few people pay attention to this, but in vain. It's all about the pressure of the water that will flow out of the tap. If the container is flat, almost horizontal, then water will flow out of it in a small stream. The higher the water column in the washbasin tank, the greater the pressure. For example, among rectangular washbasins, it is better to give preference to one that has an elongated shape. Better yet, take a washbasin whose bottom is not flat and slopes toward the faucet.

Faucet location. Recently, washbasins with a valve tap on the front wall have become very popular. Have you noticed that the water pressure from such a faucet is less than from a small 3-5 liter washbasin with a pressure tap? The thing is that in a valve tap, water pressure is lost due to the rotation of the spout of the tap itself and due to the fact that it is located not at the bottom, but on the front wall. Choose a washbasin model in which the faucet is located as low as possible. Otherwise, you will encounter such a problem - you will have to add water to the washbasin before it runs out, from about half the capacity. The reason is a loss of pressure.

How to organize heating in a washbasin

The cost of ready-made heated washbasins starts from 20 USD. This is quite inexpensive, considering that the heating device is equipped with a temperature controller from +30 to +70 °C. You can also make such a unit yourself. To do this, you need to buy a heating element with a thermostat and install it in the tank.

Important! Please note that the heating element is most effective if installed at the bottom of the container, at a level of 2 - 5 cm from the bottom. It makes no sense to install the heating element at the top.

Complexity self-installation The heating element in the washbasin is this. The heating element crashes into the tank body and the block with the thermostat remains on outer wall washbasin It is quite difficult to seal the washbasin body after insertion. You can, of course, immerse the boiler into the container through the lid without making holes in the body, then there will be no problems with sealing.

Washbasin cabinet frame

When planning to make your own washbasin with a sink for a summer house, the frame of the cabinet and the cabinet itself are the most obvious design elements that make sense to make yourself.

The easiest way to make such a washbasin is if you still have a dishwasher from Soviet times. Shape and size of old kitchen sink completely suitable for constructing a washbasin. A cabinet with an opening door and bottom, a place under the sink and the sink itself. You only need to attach a board to the finished sink body on which you can attach the washbasin container.

If the old sink is not available, then you will have to make the cabinet yourself. The cabinet frame can be made from wooden blocks with a section of 50x50 or 80x80 mm, as well as from a steel angle 40x40 mm or 25x25 mm.

Convenient height of the sink cabinet is from 85 cm to 1 m.
Take a steel corner or a wooden beam and cut 4 pieces 85 cm long.
We measure the sink that we are going to install in the cabinet. The size of the frame should be such that the sink fits easily on the edges of the frame.
Then we cut 8 pieces to fit the size of the sink, usually 50 cm.
We weld or knock the frame together.

Remember that the sink will be placed on the inner edges of the frame, so use them as a guide. After manufacturing, the steel frame must be primed and painted, since it will quickly rust in frequent contact with dampness and water.

Vanity unit and countertop for washbasin

The frame of the cabinet can be covered with different materials:

Wooden boards;
Plywood panels;
Steel sheets;
Polycarbonate sheets.
Plastic panels.

Wood and plywood will quickly get wet outdoors. Although if the wood is varnished, it can last a long time.

We cover the back and side walls of the cabinet completely, firmly securing the material to the frame of the cabinet. On the front wall of the cabinet you need to make a door, which you then hang on its hinges.

It is advisable to make the floor inside the cabinet plank with a distance between the boards of 1 - 1.5 cm, so that air can circulate, and even accidentally spilled water can seep into the ground.

You don’t have to limit yourself to just a cabinet under the sink; you can make a countertop and a convenient drying rack for dishes:

On one side or both sides of the cabinet we make a tabletop or drying rack.
Let's take it wooden boards section 25x15 mm.
We knock them together in such a way that we get a drying rack. Between the boards we make a distance of 1.5 - 2 cm.
The dryer can be made two-level, then at a height of 35 cm above the ground we make another frame for the dryer and fill the boards.

A drying rack next to the sink is convenient because you can place freshly washed dishes in it. The cups can simply be turned upside down and left to dry. Plates and pot lids can be inserted into the gaps between the boards and fixed vertically to drain excess water. And simply place pots and pans upside down on the drying rack.

It is not necessary to connect the dryer frame to the washbasin cabinet. The wooden dryer must be varnished.

Sink and washbasin drain

The sink for an outdoor washbasin can be plastic, enameled or stainless steel. The last two are the most durable and practical. You can buy a new or used sink and carefully install it into the frame of the cabinet.

Draining water from a washbasin can be organized in different ways:

Place a bucket, which is emptied as it fills.
Drain into a sewer or into a ditch.
Drain the water directly into the ground, having previously poured a 25 - 35 cm layer of crushed stone under the cabinet.

The option with a bucket is the most optimal. The fact is that in the washbasin we not only wash our hands and face, we often wash vegetables and fruits here; along the way, the tails come off and are thrown straight into the sink; also, when washing dishes, food residues are also washed into the sink. In the end waste water obtained with organic residues. It is better to take a bucket with such slop to a compost pit or heap, where the remains will rot.

It is possible to arrange the drainage of water into the sewer, but then it will not be possible to dump cleaning and food debris into the sink, as they can clog the pipe. A regular corrugated sewer pipe connects to a sink drain and is routed underground to a septic tank or drain. Some people simply dig the pipe in at a depth of 25 - 35 cm at a distance of 1 - 2 m from the washbasin, and the water simply soaks into the soil.

If desired, an ordinary cottage washbasin can be turned into a real masterpiece, especially if you use wood for decoration. But remember that wooden products It is better to put it away for the winter in a dry shed or garage. This also applies to heated washbasins.

“From the master class presented by the author, you will learn how to make a sink and drain in your dacha yourself. When you have a convenient table with a built-in sink on your site, it is very convenient, because you can quickly and easily wash vegetables, fruits, berries, herbs directly from the garden, and cut them right there on the table.

The design here is quite simple, you will need to assemble a table with a height of 90 cm, a tabletop width of 60 cm and a length of 120 cm, the author provided these dimensions with his own, but in each case there may be nuances and you need to do it according to yourself and your height.

The table itself can be assembled from boards and timber, and the same boards (for example, from a pallet) can be used as a tabletop. You also need an old sink and faucet. And so, let's look at the whole process of assembling the table and installing the sink, what exactly did the author need?

Materials
1. sink
2. water hose
3. board 25-30 mm
4. beam
5. faucet
6. faucet
7. PVC sewer pipe
8. gravel
9. screws
10. silicone sealant
11. nails

Tools
1. jigsaw
2. drill
3. screwdriver
4. screwdriver
5. hacksaw
6. hammer
7. pliers
8. roulette
9. pencil
10. corner

The process of creating a sink and drain at the dacha with your own hands.

By installing a table with a sink in your dacha, you will make your life a little easier. The first step will be to assemble the table itself, for which the author used a 25-30 mm board and timber. The master also provided a drawing with detailed description and sizes. In each individual case, select the size according to your preferences so that it is convenient for you to use the sink and the table itself.
Next, the table legs are made according to the given dimensions, namely, 2 boards are taken and sewn together with self-tapping screws in the form of a corner like this.

You need to make 4 identical legs.

Small cuts of timber are screwed into the lower part.

Cross members are mounted on the resulting supports, thereby fastening the legs of the future table.

The longitudinal bars are also attached at the bottom.

And at the top accordingly.

For better reliability of the entire structure, it is necessary to secure a few more bars in this position.

After which a tabletop is installed, which can be made from the same board.

Next, you need to cut a hole in the countertop for installing the sink. On the surface of the table you need to mark the shape of the back of the sink, then drill a hole with a drill, then insert a jigsaw blade and cut out the intended outline.

Then the sink is installed, first apply a layer silicone sealant on the skirt of the sink, so that later during operation water does not accumulate at the junction of the sink and the table.

After which the faucet is installed.

And it is connected to the water supply through a hose.

This is such a wonderful countertop with a sink.

Now the most important thing is “draining” so that the water leaves the sink safely and does not pollute the area, you need to make a drainage hole. And so, you need to dig a hole 1-1.5 m and dig in, for example, a barrel with holes made in the walls, or you can use sewer pipe large diameter, also with holes, install in a hole and fill with gravel. The sample is shown in (photo).

Not everyone has running water in their summer cottage, although the need to use water arises constantly: a huge number of times we rinse our hands after digging in the garden or working in the garden, washing dirty vegetables and herbs from beds, fruits from trees, berries from bushes, and also dishes. All these actions will become much easier to implement if we have a washbasin in the country. It will not be possible to install a sink inside the country house due to the lack of running water. This can be implemented in the garden or next to the gazebo where lunch meals usually take place.

What could a country sink look like? Is it difficult to build a full-fledged washbasin for your dacha with your own hands? Which ready-made solutions can you find it on sale? Let's figure it out.

Specifics of a summer cottage

To begin with, let's formulate the differences between a summer cottage and an ordinary residential building in the plan that interests us.

How should a garden sink differ from our usual kitchen sink?

For summer cottages, it is typical that there is no constant water supply. The source of water may be a well; In addition, water for irrigation is often supplied on schedule. If your dacha does not provide storage capacity for water raised to a height to create pressure, it is advisable to provide such a container above the sink.

Let us clarify: if you want to ensure the maximum comfort available in nature, it would be a good idea to take care of heating the water.

Local sewerage in a summer cottage is also the exception rather than the rule. As a rule, a cabinet under a cottage sink is equipped with a shelf on which a regular bucket is placed to collect waste. After washing or washing dishes, soapy water simply splashes out away from the beds.

From these positions we have to explore market offers.

Ready solutions

So, what can stores aimed at summer residents offer us?

For indoor installation

These solutions differ in that their appearance is given certain attention. In fact, even in country house I want to see beautiful household items. Typical material cabinets - laminated chipboard (laminated chipboard); The sink can be enameled or made of stainless steel.

A water storage tank is mounted above the sink on the back wall of the cabinet. As a shut-off valve, a regular water tap or a simple mechanism with a plug is used, which lets water through when lightly pressed from bottom to top. The material of the tank is plastic (usually polypropylene or polyethylene), galvanized steel or stainless steel.

A bucket for drainage is usually installed inside the cabinet; however, nothing prevents you from using this space for storing dishes and other kitchen utensils, and draining water with a thin sewer or corrugated pipe. To filter it, a shallow well is dug into the ground. drainage hole, covered with rubble, or a ditch.

Captain Obvious suggests: on a site with a slope, it is better to discharge wastewater below the house on the slope.
We are in no way interested in washing away the foundation.

Let's analyze the description of a product of this class in more detail.

Our example will be a sink with a cabinet for a summer house with the creative name Leader 10525.

The material of the cabinet is laminated chipboard. Several colors are possible.
The sink is made of stainless steel. The water tank is made of polypropylene.
Tank capacity – 22 liters.
The tank is equipped with a heating element with a nominal power of 1.25 kW. Heating 22 liters of water to a maximum temperature of 60C takes about half an hour. The exact time depends on the starting temperature.
Dimensions products - 1330x500x500 millimeters.
Retail price – 3850 rubles.

For outdoor installation

Outdoor installation implies slightly different requirements for the product. First of all, to the materials used for its manufacture.

In addition, aesthetics take a back seat. In fact, a sink that is too beautiful is likely to change its owner the first time you leave the dacha.

Let's flesh out the differences.

Wood in all types and especially laminated chipboard are extremely hygroscopic materials. A cabinet made of solid wood or plywood will quickly dry out under the rain and sun, chipboard will swell and crumble into dust in one summer.

As a rule, a metal cabinet is used for the street - a bare frame or load-bearing walls made of steel with an anti-corrosion coating. Somewhat less commonly, the sink stand is made of hard plastic tubes.

The sink is plastic or (somewhat less commonly) enameled. Plastic gets dirty easily, but it is extremely cheap and does not corrode.

A typical product of this class, which will serve as an example for us, is the “Street” washbasin with the “Comfort” water heater.

Washbasin “Street”.

All parts, except the heating element, are made of plastic.
The stand is tubular, collapsible. The side arches are separated from the frame for the tank and the spacers between them. When disassembled, the structure easily fits into the trunk of a car.
Tank volume – 18 liters. This is quite enough to wash a moderate amount of dishes or wash three or four people.
Heater power – 1.25 kW. Actually, large electrical power is rarely in demand in dacha electrical equipment: typical wiring in gardening societies is aluminum with a cross-section of 1.5 millimeters. It is clear that its overload does not promise anything good for the owner.
The size of the sink is 350x400 millimeters.
The cost of the product is more than modest - 1650 rubles.

Related Products

A ready-made cabinet with a sink for a summer house is not the only solution that can be found in the relevant stores.

A plastic, aluminum or steel washbasin provides a minimum of comfort, but allows you to do without outside help when washing your hands. Think about how many times a day you have to ask a family member to pour water on your hands.

An advanced version of the washbasin - a large plastic tank with heated water - allows you to wash dishes and wash your face with relative comfort. The ability to heat water is especially valuable in cold weather.

The controls are located on the front panel; The ceramic faucet in the water tap ensures long-term operation and prevents water leakage. The water heater is equipped with a thermostat and an emergency relay that turns it off when it overheats (for example, when the tank is emptied in heating mode).

The tap is designed for installation on a plastic or metal container. Its presence can turn a can or canister into a fairly convenient washstand.

Another simple device that provides a minimum of comfort at a minimum cost and is extremely easy installation. The 7-liter polypropylene tank hangs on the wall using the included metal brackets. The cost of the washstand is only 230 rubles.

The sink, made of polypropylene, can be installed on brackets or a cabinet. The product is solid cast and equipped with a grate at the outlet. Overall dimensions of the sink – 40x50x18 centimeters, capacity – 21 liters; the outlet is threaded for attaching a siphon or corrugated pipe.

And in this case, the main advantage of the sink is its minimal cost: it will cost the owner 150 rubles.

Self-production

Of course, the sink itself at the dacha is not made with your own hands: we just have to combine several products from the “related products” section with the materials that are at your disposal.

Is it worth spending time on this if a ready-to-use cabinet with a sink and a bulk water heater can be purchased for about 2,000 rubles?

In general, it's probably not worth it; however, we will present a number of circumstances that can push the owner of a summer house to the creative process.

Old furniture often ends its life life path V country house. If you already have a kitchen cabinet, is it worth buying a design that includes exactly the same cabinet?
Country houses rarely have a large area. Lack of space or layout features may prompt non-standard placement sinks with the corresponding requirements for its size and method of fastening.

So, how to make a sink in the country? Of course, we are not talking about the most primitive design of a washstand and a trough: I think that the reader does not need advice to build this masterpiece of engineering. Let's try to build something that you won't be ashamed of in front of your guests.

Washing

From the point of view of a combination of beauty and practicality best material- stainless steel. Since the stream from the tank will not hit the sink with high pressure, we don’t have to worry about the thickness of the steel and the various stickers on its outer surface that dampen the sound: we need the most inexpensive sink with dimensions that will allow you to comfortably wash the dishes.

The size is selected depending on the space you have. As a rule, sinks have dimensions of 50x50 or 50x60 centimeters.

Please note: the greater the depth of the bowl, the less splashes will fall on surrounding objects.
In addition, it is better to take a sink with a stopper: in conditions of shortage hot water being able to put it in the sink when washing dishes is very convenient.

Cabinet

Its width and depth are tied to the size of the sink. The optimal height of the sink rim for a person of average height is 85 – 90 centimeters. If you intend to mount the water tank on back wall, it should be made about 130 - 140 cm high.

Which material should you prefer? If you don't have welding at your disposal, wood products are an obvious choice.

Several options are possible:

Plywood with a thickness of 12-15 millimeters combines sufficient strength with beautiful texture surfaces. It will look quite presentable with a varnish coating.
Thin OSB can be used to sheathe a timber frame. And this material looks good and very unusual under a layer of varnish.
Finally, the timber frame can be sheathed wooden clapboard or tongue and groove floor board.

In all cases, the cabinet will need reliable protection from water: wood is an extremely hygroscopic material. Most resistant to adverse effects environment polyurethane-based yacht varnish; not much inferior to it is parquet polyurethane varnish, intended for indoor use. In extreme cases, PF-170 or NTs will do.

If the material has noticeable surface defects, it is better to prefer paint to varnish. For our purposes, alkyd enamels PF-115 are suitable; In addition, the author had extremely pleasant impressions of water-dispersion rubber paint based on acrylic resins. All irregularities are pre-puttyed.

The number of layers of varnish or paint is from 4 to 6. Before applying the first layer, the assembled cabinet is sanded; Sanding with scratch paper is also required after applying the first layer. The fact is that varnish or paint causes the pile, thin fibers of wood, to rise, and its surface becomes rough.

Bulk tank

It is attached in such a way that the tap is approximately 15 centimeters above the edge of the sink. When washing dishes, a ball or screw water tap is more convenient; the keyboard, however, is noticeably more economical.

Waste disposal

An excellent alternative to a bucket under the sink is a drainage hole. She digs at a distance of at least a meter from the foundation of the house; it is desirable that its volume be at least twice the volume of the water tank.

The pipe from the sink is led into a hole below ground level; if you plan to use water in winter, then both the pipe and the hole are buried as deep as possible. The pipe is additionally insulated with a shell made of foamed polyethylene.

In order for the absorption surface to be maximum and the walls not to crumble, the pit is filled with drainage - crushed stone, stones from the site, broken bricks, etc. If necessary for winter operation, the drainage is insulated on top with a sheet of foam plastic.

Conclusion

We hope that the article will help you settle into your dacha with maximum comfort. The video in this article will offer you additional information about country sinks. Good luck!

Gallery

It is very difficult to do without a washbasin in the countryside. There is always a need to wash your hands, dishes, vegetables, fruits. Not every country house has running water, but everyone wants to comfortably use a convenient and practical washstand. How to make a washbasin at the dacha with your own hands, photos and videos of the manufacturing stages from scrap materials are given in the article.

Do-it-yourself washbasin for a summer house, photo

Washbasin for a summer house made from scrap materials

There are many options that you can easily do with your own hands and not spend a penny from the family budget. Summer residents most often use the following models of washstands, including:

hinged - the most popular model, it can be bought inexpensively at any hardware store or made from scrap materials, for example from a plastic bottle;
A portable washbasin on a counter is a very convenient and practical model. The structure can be installed anywhere on the site, since the structure is lightweight and quite mobile;
a washbasin with a cabinet is a stationary option; it is often installed in a country house near the house or indoors;
a heated washbasin is decided to be installed by those summer residents who use country house all year round.

Washbasin with cabinet in the country

The manufacture of all of the listed structures is simple and every summer resident can cope with the work. A simple option can be made using a regular plastic bottle. Different volumes of bottles allow, if necessary, to make a spacious wall-mounted washbasin with a spout that will last for more than one season.

How to make a washbasin in the country with your own hands from a plastic bottle, video:

Having made such a washbasin, it is worthwhile to provide for draining the used water. However, those summer residents who rarely use the washstand do not drain at all, and the water pours onto the ground. This method is not suitable if the washbasin will be used regularly. In this case, it is recommended to drain the used water into a compost pit or organize a primitive drainage system. To do this, you need to remove the top fertile layer of soil - about 30 cm. Pour crushed stone into the resulting depression and install a drain hose. Water will easily seep through the rubble and it will always be dry next to the washbasin.

Washbasin for a summer residence

Do-it-yourself washbasin for a summer residence from scrap materials

A do-it-yourself wall-hung washbasin in the country from a plastic bottle has a number of disadvantages. For example, the container size is small and the water will run out quickly. In addition, the capacity has an unattractive appearance. It is more practical to use a metal or plastic canister to make a washstand.

A hole of the required diameter is drilled in the bottom of the canister.
The faucet is installed using rubber gaskets to achieve tightness.
Under the canister you need to provide a washbasin with a drain, as shown in the photo.
For lead sewer water drainage is dug out or pipes are laid to carry waste water to drain hole.

The photo shows a wall-mounted washbasin made from a plastic bottle with a spout

The principles of making a wall-mounted, portable or with a cabinet washbasin are the same, and if you equip it with a countertop, you will get a rather attractive design that will be convenient to use.

Video about making a washbasin at the dacha with your own hands from scrap materials:

How to make a washbasin at the dacha with your own hands, photo, design diagram or drawing is a fairly popular request on the Internet. Even a builder without experience will be able to perform a number of simple steps. By selecting budget option, you can even save a lot of money. To do this, you should use available materials available on the farm.

At the dacha or in the garden, you often have to do work that can leave dirt on your hands. Nowadays, almost every summer cottage has a washbasin on the wall of a house or barn. Most common form of this product It is a small container with a pressure spout that is hung on the wall.

These washbasins are quite easy to use and cost little. Some craftsmen themselves make a similar galvanized washbasin for their dacha; its service life is much longer. Making a washbasin for your dacha with your own hands is quite simple, you just need to know the technology.

Types of structures

Few people know that this type Personal hygiene products can be made not only a practical thing, but also part of the exterior of the entire garden. With my own hands You can assemble several types of washbasins for your dacha:

From plastic bottles.

This design is simple in its implementation, and in terms of cost, no one, even the cheapest “device” from the store, can compare with it.

"Moidodyr".

This washbasin is a full-fledged workplace. Here you can wash dishes and vegetables.

Portable, on stands.

A portable washbasin can be placed in any convenient location, for example, near a table or barbecue, and after use, transfer it again to the storage location.

Mounted from a canister.

A wall-mounted washbasin, assembled using canisters, is very convenient due to its volume. There is no need to pour water into it every time you need to wash something.

Each of these types has a special design, and any amateur summer resident who has a pair of necessary tools. After all, each of the gardeners sooner or later thought about how to make a washbasin in the country with their own hands.

Washbasin made of plastic

Everyone at their dacha has several empty and unnecessary plastic bottles; you can use them to make a plastic washbasin for your dacha. They remain from drinks that are brought with them and drunk after work or during rest. You can easily and quickly build an outdoor wall-mounted washbasin from them.

The simplest washbasin

There are many ways in which plastic containers can be easily converted into personal hygiene products.

But they all boil down to simple steps:

Rinse the container to remove any remaining unfinished liquid.
Next, you need to cut off the bottom of the bottle.
The resulting tank must be fixed on a vertical surface so that the neck faces down.
The cut off bottom can be left and used later as a cover for the washbasin.

The design is almost ready, then those who don’t want to bother too much can leave everything as is and pour water through the top. To open such a tap, just turn the lid until water flows from the tank in a thin stream. But this design is not perfect, since if you open the cap too much, you can accidentally open the bottle completely and all the contents will spill out.

Therefore, many craftsmen are trying to come up with interesting variations of various mechanisms for supplying water, allowing them to wash their hands without the risk of being doused with water. Here are a few options that are most often found in such designs:

Take a large diameter nail and blunt it. Next, you need to remove the lid of the wash bottle and make a hole in it into which the nail should fit freely, but it should be smaller than the head. Next, the structure is assembled in such a way that when the lid is screwed on, the cap is inside the structure. Now, if the container is filled with water, it will hold it, but if you lift the nail, water will flow out of the opened hole.

This scheme has several disadvantages: firstly, the nail will rust over time, polluting the water, and secondly, such an outdoor sink for a summer house will constantly leak, since the head of the nail is uneven.

It's even easier to make a hole in the top of the lid. Then you don’t have to turn and open it completely; just turn the cap on the bottle a little and water will flow out of the hole.

There is only one downside to this design. It is quite difficult to adjust the required width of the water jet.

A simpler, but more expensive, scheme may be with a simple water tap instead of a lid. It can be purchased separately. Or remove it from old technology. The main thing is to choose the correct diameter that matches the width of the neck.

Also, syringes, taps from boxed wine and other improvised means are used as taps and “spouts”, here, as they say, whoever is good at what. Do-it-yourself washbasin for a summer house, photos and videos:

Washbasin made from a plastic bottle

This type of washbasin is quite simple both to manufacture and to use, but from a practical and aesthetic point of view, they are clearly inferior to their competitors. You can hang the washbasin on a tree branch using a rope.

Mounted from a canister

Models made from canisters are a more advanced version of washbasins made from plastic bottles. They can be made from any large container, ranging from plastic canister, ending with an old saucepan.

Regular canister

Making such a model is quite simple. To make it you will need any empty plastic or metal container with an opening top and a water tap. Next you should do the following:

In the lower part of the container, 1 - 2 cm from the bottom, it is necessary to make a hole, the diameter of which should be equal to the diameter of the tap inlet.
Next, you need to fix the tap in this hole. You can do this in three ways:

If the tap is metal, then it can be fixed using two washers, two rubber gaskets and a nut. The washers and gaskets are positioned so that one piece is placed on each side of the hole on the faucet. The nut is screwed on from the inside.
If the crane and container are made of metal, then the crane can be welded to the container, then the structure will not be collapsible, as in the previous version, but at the same time, it can last much longer.
The last method is best used when working with plastic. If both components are made of plastic, then hot melt adhesive can be used to connect them.

Type of design

Such washbasins for the garden and cottage can be hung on the wall, or you can build a small structure that will hold it at a height of 10-15 cm, then it can be placed on the table. Often, under this type of washbasin, a sink with a drainage system is installed, which directs dirty water into the drain.

Portable washbasins on racks

This outdoor washbasin for a dacha does not have such large selection variations of designs like the previous one, however, it is much more practical for a number of reasons.

The main advantage can be understood based on the name of this design, since, unlike most types of washbasins, they can be carried and used outside in the country house. It is due to mobility that craftsmen from gardens and dachas take on their production.

Washbasin on racks

To make such a washbasin, you need to make a container. This can be done according to the description presented a little higher, in the section “Attachable from a canister”. In addition to the tank, you will need a base on which it will hang. To make it you can use wooden beams, but better - a metal rod with a cross-section of 5-7 mm. The fact is that structures from last option materials are smaller in size, but lighter and more durable. Do-it-yourself washbasin for a summer house, photo:

In order to connect the rods, welding will be required. The lower platform should be wide to give the structure stability. There are 2 popular variations of support elements:

In this case, the washbasin has 2 legs, which are located on two parallel rods. Due to the two legs, it is difficult to tip the structure on its side, and supporting parallel rods prevent it from falling backward or forward.
"H"-shaped. This scheme is similar in appearance and properties to the previous one. The only difference is an additional rod; it must be welded perpendicular to the leg supports, so that the letter “H” is formed. This additional element will help protect the structure from the legs moving apart.

The legs, like the support, are made of rods; their length can be different, but not more than one and a half meters, otherwise the structure may bend over time under the weight of the water in the container. To keep the tank on its “legs”, you can weld two hooks. In addition, it can be hung, or a small “basket” can be welded into which the container will need to be inserted.

Appearance

This design It is quite simple to construct and does not take up much space; it can be carried and installed in places where it is necessary to wash your hands. This unheated garden washbasin is very convenient to use.

Washbasins made of wood are less mobile due to their weight. Because portable structures It is quite difficult to find from this material.

"Moidodyr" with a bedside table

The most solid version of a washbasin that you can build with your own hands is garden plot, is considered “moidodyr”. This design can replace a small outdoor kitchen in its functionality. It can be installed on the veranda, inside the house or outside. The product is a full-fledged washbasin with a cabinet and a sink. The cabinet is extended, resulting in a table that is convenient to use for cutting food. The washbasin itself hangs on the wall, which is securely attached to the cabinet.

The simplest scheme

To make it you will need a lot of materials, however, you don’t have to run to the hardware store for them. To assemble such a structure, what is left in the barn after building the house may be suitable:

old boards and beams - for the frame (you can use metal corners);
lining, plywood, plastic are perfect for cladding;
Thick plywood, starting from 7 mm, can be used as a tabletop.

The most important attributes of this design are the sink and the water tank, which is installed above it. You will most likely have to buy a tank, but you can make it as described above from any convenient container. But you can take an old sink, left over from the old kitchen.

A hose is connected to it, the free end of which must be lowered into the drainage ditch to drain dirty water. At the same time, it is necessary to install a siphon in the structure, just like in an apartment, so that bad smell and bacteria from the table did not spread around the sink. Especially if he is at home.

Option 1

Wooden beams are used as a frame, which are covered with cladding on top. “Moidodyr” consists of a cabinet in which the sink is installed and walls on which the washbasin is hung. Therefore, the design is assembled based on the dimensions of the tank and sink. A pipe with a siphon is connected to the latter, leading to a drainage hole to drain waste and dirty water.

So, the cabinet should be slightly smaller than the sink (if it is counter-mounted), or larger than it by at least 2 cm (when installing a mortise version). The height of the cabinet can be different, the main thing is that the person does not hunch over when washing dishes/hands. The front part of the cabinet is hung on hinges, which creates a door. In addition to the sink, the cabinet may also have a countertop.

Option 2

The wall is made simpler; it rests on the 2 outer beams of the back of the cabinet, which must be extended by at least one meter. If the structure exceeds a meter/one and a half in length, then there should be three support beams. The trim is made from the same material as the doors and side walls of the cabinet. The tank is attached to the wall using hooks or a welded structure. Free space, if available, can be used to build shelves or hooks for towels, knives and other kitchen utensils.

Sometimes "Moidodyr" is supplied heating element. It is necessary if the washbasin is used in the cold season. Installing a water boiler on a washbasin will allow you to wash dishes in the garden or at the dacha in warm water even in the cold season.

Bottom line

Making washbasins for your garden and dacha with your own hands is quite simple. At the same time, if you don’t have experience or time, you can start with a simple design, mounted from a canister, and gradually build it up to a large “Moidodyr”.