Where is the best place to build a hut? Prefabricated huts for small children

Everyone should know how to build a temporary shelter over their heads during a hike. After all, you don’t always have a ready-made tent or sleeping bag with you, and a roof over your head is the main thing, in addition to food and getting water, that a person thinks about in the forest, especially if the trip takes place in winter conditions. You can learn more about how to build a hut in the forest with your own hands.

A shelter in the forest should provide protection from wind, rain or snow. It is easiest to build a hut in the forest, since all the materials necessary for this are present. There are three types of temporary shelter: a free-standing hut, an attached hut, and one built in a recess. In addition, by design they are hipped, single-pitched and gable. Before you start building a hut in the forest, you need to find a suitable place. This should not be a depression in a narrow gorge, a river bank or the bottom of a canyon, or the foot of a mountain.

If you need to make a hut in a mountain forest, you need to choose an attached type shelter, one or two sides of which will be made of wood or parts of rock. Installation is carried out in such a way that the entrance faces the direction opposite to the top. Along the perimeter homemade tent you need to dig holes to drain rainwater.

If you need to build a hut in a flat forest, you need to choose a place based on weather conditions. In cold, dry weather, you need to choose a place in a depression, and in rainy weather, on a hill. In order to build a shelter, you will need an ax, rope, and knife. If you don't have rope, spruce roots are an excellent substitute. Other tools are not so important, and usually you don’t have anything with you other than what’s listed.

Hut

A lean-to type shelter is a canopy that protects from the wind and reflects heat from the fire like a screen. A hut is built between two trees. Between them you need to fasten a crossbar made of poles, to which the rafters are fixed at an angle of 45-60 degrees. Several more poles need to be fixed to them parallel to the ground to form a kind of lattice, the frame of which needs to be covered with vegetation that protects from wind and precipitation. Coniferous spruce branches or branches with large leaves are well suited for this. The branches are attached to the crossbars, starting from the first lower level to the upper one. This way, the water will flow down the wall without getting through the foliage. Several short logs are placed on the ground, with thin poles placed on top of them. You can lay spruce branches on top of them, and the “bed” is ready.

Another option for a lean-to shelter is built next to a broken tree. You need to find a tree so that the break is no more than two meters above the ground. The part of the trunk lying on the ground is covered with long branches as a roof deck, and the ground under the trunk is also covered with branches.

One of the options for a gable hut can be built if you add a second side made of poles, crossbars, covered with spruce branches or branches to the above-described single-slope shelter.

The second option of the gable type consists of a sequence of actions:

You need to find two strong sling racks, thin rods and a long pole as a support.
The posts are installed in the ground approximately a third of their length.
A horizontal pole is installed on the racks.
Thin branches are attached to the floor at an angle to the poles, serving as rafters.
From above, the rafters are covered with branches with foliage, spruce branches, and grass.
The covering material is positioned from bottom to top to prevent water from penetrating inside.
You need to place your fire at the entrance to the hut.

Tent hut

A tent hut is built from young, thin, long poles, which are cut off from excess branches and foliage, and installed in a cone. They can be attached to each other or around a tree trunk. From above it is covered with grass and branches. If the tent hut is made large, you can place a fire inside it. To allow smoke to escape from the top, you need to leave an uncovered part. But at the same time, the fire should not be too large; when lighting, use only hardwood to avoid sparks.

Shelter in a recess

A temporary shelter built in a recess is something between a dugout and a hut. To do this, you need to find a small hole in the ground or dig it yourself. Thin branches with covering material (spruce branches, grass, reeds, leaves) are mounted on top of the shelter; inside the structure, the ground surface must be covered with the same if there is no sleeping bag.

Ukrtie in winter

In winter, you can also build a hut that protects from snow and wind. The main thing is to have a warm sleeping bag with you in winter. To build a winter hut, you need to find a suitable place on a hill, clear it of snow to create a small depression. Next, you need to prepare the required amount of coniferous spruce branches and poles. The spruce branches must be cut from the lower branches of the trees. Poles can be used from old, dry trees; they do not have to be young trees. Part of the chopped coniferous spruce branches should be used to lay out the floor of the future structure in such a way that there are no protruding branches. Poles are installed on both sides of the future hut, additional supports are placed on top of the frame, and the poles are tied with rope at the places where the load is applied. Then spruce branches are laid on top of the frame in dense rows without gaps or cracks. The sides of the hut also need to be well covered with coniferous spruce branches, while at the same time covering the walls with bricks of snow, if it is dense. The entrance to the shelter can be covered with hanging spruce branches. Such a structure will be warm and spacious enough to spend the night.

Summer has come, which means you can safely start building a hut. But here's the problem: you don't know where to start. Don’t be discouraged, because in today’s article we will look at the main types of these structures, and also describe installation instructions that will help you quickly and easily build a hut.

Where is the best place to build a hut?

It is immediately worth noting that building huts near mountain rivers, in open clearings, near single trees and under rocky slopes is strictly prohibited. This is not only unsafe, but also extremely inconvenient. Basically, these structures are built on flat forested areas, where there are a lot of dense plantings that will do an excellent job of protecting the hut from drafts. However, a summer cottage plot is still considered an ideal option for construction. Here, if necessary, you can ask your parents for help, and also go to the house at any time.

An excellent place to build a hut is a forest lawn

Options for children's huts

The most popular among children are gable and single-slope huts and wigwams. They are perfect for both forest and country areas, and their construction is not difficult and takes a minimum of time.

The first option is a gable hut

The construction of a gable hut must begin with the construction of a frame, which, in turn, will be made of a pole and a spear. The dimensions of the building will directly depend on the size of these elements, so immediately estimate how many people the hut will be designed for. The rods must be driven vertically into the ground a third of their length. This is done so that in the future these elements do not wobble and are stable.

Scheme of the design of a gable hut

After this, place a pole on the slingshots and, if necessary, secure the joints of the elements with wire or strong rope. Well, some of the work is already behind us. Now you will need to collect a few more thick tree branches (poles), which will later become a support for laying roofing material such as reeds, hay, straw or spruce paws. By the way, we recommend placing the poles close to each other. In this case, there is no need to cover the walls with anything else. However, in most cases, the side poles are placed at a distance of at least 20 centimeters from each other. If you notice that the frame is not reliable enough and could collapse at any moment, strengthen it with transverse branches that need to be attached to the poles.

Now is the time to lay the sheathing with spruce branches (or other available material). In this case, you need to start work from the very bottom. This is done so that each subsequent row covers the previous one. The result will be reliable protection the interior of the hut from moisture. Build the back wall of the structure in the same way, leaving only the entrance open.

As a result, you should end up with a structure like this:

The second option is a lean-to hut

The construction of a lean-to hut will be much faster and will take even less effort from you. First, proceed according to the same principle: use two spears and a long pole to install the supporting frame of the structure. After this, make the walls of the hut, again, as described earlier. To speed up the construction process, you can replace the spruce branches with any water-repellent fabric or tarpaulin. Attach the covering material to the frame structure from above using ropes, and press the fabric from below with a stone or log. Ready!

It is better to secure the covering material of the frame of a lean-to hut with ropes

The third option is a wigwam hut

The wigwam hut owes its name to Indian dome-shaped buildings. To build it, you first need to draw a circle on level ground, the area of which is enough for you and 2-3 friends. After this, dig several poles along the edge of the circle, connecting their tops in the form of a bundle and be sure to fasten them in several layers with tape, wire or a reliable rope.

It will be very cool if the support branches of the wigwam hut are planted with climbing plants

This completes the fabrication of the frame. Now all that remains is to make a shelter. There are two options here:

Plant all support branches with climbing plants. Decorative beans are ideal for this task, the delicate green leaves of which go well with white and red inflorescences. The result will be a very pretty building.
Brightly colored fabric can also be used as a covering material. If you don't have colorful fabric, take a plain fabric and paint it with waterproof paint. The canvas will need to be cut out in the form of a semicircle, the radius of which should be equal to the length of the side support poles. Sew ties along the rounded edge of the fabric and in the center, and also attach them to poles stuck into the ground.

By the way, sunflowers can also act as supports for the frame of a wigwam hut. You need to start planting them in the spring and do this along a circle drawn on the ground, leaving a few centimeters for entering the shelter.

Children's hut made of fabric - construction in a few minutes

A children's fabric hut can be made in just a few minutes

Children's tent made of fabric - ideal option for a few days' rest. If you prepare all the materials in advance, its construction will only take a couple of minutes! You will need a two-meter (in width) and four-meter (in length) canvas made of dense fabric, two vertical supports that must be placed at a distance of two meters from each other, a strong rope at least three meters long, as well as pegs for tensioning the canvas.

To build a hut made of fabric, it is enough to pull the rope horizontally between two supports and fix it. Throw the fabric over the stretched rope and align its ends. After this, attach the edges of the canvas to the ground using pegs. It's done!

That's all, choose the option you like and run to build a hut with your own hands. Don’t forget to use your imagination and build an interesting and colorful building where you and your friends can spend time comfortably.

Don't know how to build a play hut for your child and his friends? Are you at a loss where to start? Our article examines all the main types of hut designs and provides detailed instructions installation instructions, following which you will easily cope with this task.

Everyone in childhood built forts out of pillows and bedspreads. But these structures stood for a couple of hours at most. A children's play hut is a much more durable structure where a child can relax, develop and play both indoors and outdoors.

Basic safety requirements

Parents should make sure that the playhouse is not only interesting and cozy, but also safe. If wood is used for the frame, then the bars must be sanded and coated with paint or varnish so that the child does not accidentally drive in a splinter. All fastenings must also be hidden from children's eyes and hands. The design should not have sharp corners and hard materials (stones, metal).

A sufficient amount of air must flow inside the structure. If the hut is fabric, you need to make windows; if the house is covered with branches or spruce branches, gaps are required. For the same reason, you cannot cover the hut with film.

You definitely need to think about the correct location of the hut. Do not place it in drafts, away from adults or in the sun. There should be no objects or places that are potentially dangerous for children near the structure.

Gable fabric hut

This is the simplest construction of a hut. For very young children, a gable hut can be built by simply throwing a sheet or towel over a stretched rope. For slightly older children, a folding hut on a wooden frame is suitable.

Required materials for the frame:

four pine bars 25x50 mm, 1.2 m long;
round wooden rod with a diameter of 20 mm, a length of 1.2 m;
drill with a feather drill with a diameter of 20 mm;
pencil;
roulette.

Materials and tools for the awning:

fabric 1.2x2.2 m;
sewing machine;
linen elastic;
threads

Operating procedure:

Measure 15 cm from the top edge of each of the four bars. Mark the location with a pencil.
Now you need to drill a hole with a diameter of 20 mm with a drill.
When combining two bars, you need to make sure that the holes match.
Now you need to push the round rod through both holes. The grip needs to be fairly tight to securely hold.
Thread the second end of the rod into the holes of the remaining two bars. The frame is ready.
The fabric for the awning needs to be folded 1 cm around the perimeter using a straight stitch. Required dimensions tent 1.1x2.1 m.
Cut four pieces of 10-12 cm long from the elastic band.
Make a loop from each elastic band and sew it in the corners of the awning.
Now all that remains is to throw the fabric over the crossbar of the frame and secure it to the legs using rubber loops.

The hut of this design can be adjusted in height and width, it is easy to assemble and disassemble even for one person. It is also convenient because when disassembled it takes up very little space.

Children's hut "Wigwam"

The frame for the “wigwam” can be long wooden poles, bamboo sticks or PVC pipes. The walls can be made of fabric - such a hut can be disassembled and stored for a long time. A disposable hut in the forest or at the dacha is covered with spruce branches, but such shelter is short-lived.

To build a fabric “wigwam” you will need:

4 PVC pipes with a diameter of 20 mm, a length of 1.7 m;
8 pipe caps;
rope or shoelace;
5 m of heavy fabric 1.4 m wide;
fabric 1x1.2 m for pipes;
threads

Operating procedure

According to the plan, you need to cut the fabric. All sizes include 1 cm allowance.
First you need to hem the edge of the upper part of the front wall with a length of 12.7 cm. We also hem the 91 cm sides of both lower elements.
Now you can sew all parts of the front wall together.
Now you need to hem the upper edges of all three sides. Align them in height, place the bottom so that the final height of the side walls is equal to the height of the finished front wall.
The fabric for the corner needs to be folded into a kind of loop-cover for the pipe. This cover is placed between the adjacent walls of the “wigwam”, and the whole thing is sewn together. The same needs to be done with the remaining corners. The result is a finished tent.
You need to step back 10 cm from the top edge of each pipe and drill a small hole.
A cord is threaded through the holes, which firmly ties all the pipes together. At this stage, an awning is placed on the frame.
The ends of the pipes are closed with caps, and that’s it - the “wigwam” is ready!

Hut made of branches and living plants

In order to build an original hut from living plants at your dacha, you just need to drive high poles into the ground in a circle - this will be the frame. Plant along the perimeter of the frame climbing plants, such as clematis, morning glory or grapes. The obvious disadvantage of such a hut is the long time it takes for plants to grow, so such a house will not be interesting for children.

You can quickly build a hut from willow, which will require a lot of long branches (the longer, the higher the house). Simply drive the branches into the ground and intertwine the tops tightly. To make the walls more dense, you can cover the vine with spruce branches or simple straw.

Tent with PVC pipe frame

A tent of this design takes up a large area, but can accommodate a whole family. It is very light, easy to install, and when assembled it takes up little space.

Necessary tools and materials for the awning:

sewing machine;
dense fabric 2x3.5 m;
threads;
roulette;
pencil;
scissors;
pins.

For the frame, PVC pipes with a diameter of 20 mm and plastic connectors are used.

Frame tools:

A - pipe 146 cm long, 3 pcs.;
B - pipe 152.5 cm long, 2 pcs.;
C - pipe 122 cm long, 2 pcs.;
D - pipe 64 cm long, 4 pcs.;
E - pipe 80 cm long, 4 pcs.;
connector for pipes with a diameter of 20 mm, 4 pcs.;
PVC elbow 45 degrees with a diameter of 20 mm, 4 pcs.;
T-connector for pipes with a diameter of 20 mm, 4 pcs.;
triple plastic corner for pipes, 6 pcs.;
PVC fitting with male thread, 6 pcs.

Making a tent cover:

Cut a piece of fabric 1.6 x 3 m, add 1 cm at the edges. This is the main covering of the tent.
From the remaining fabric, cut three strips 10 cm wide and 140 cm long. Each short side of the strip needs to be folded 1 cm. These are fastening strips, with their help the awning will be fixed to the frame.
Bend the long sides of the strips 1 cm and iron them.
From the wrong side of the main cover, sew one edge of the strip to the short side A. The second edge is sewn at a distance of 4 cm from the first. The same must be done with the fastening strip, which is located on the opposite side of the frame.
To find the middle of the awning, you need to fold the canvas in half. Step back 2 cm from the fold line in each direction and mark with a pencil. The third strip needs to be sewn here.

Assembling the tent frame:

First you need to secure the elbow and T-piece together using a pipe connector.
Now we will make six 90-degree angles: four for the bottom of the tent and two for the ridge. To do this, you need to attach the fitting to the top of the triple angle.
Next, assembling the frame is similar to assembling children's construction set. First, the front and back wall, then they are connected to each other by crossbars.
The final step is to install the tent along with the cover.

An older child can safely be involved in the construction of a hut. It’s also very easy to keep little children occupied: just give them bright colors and let them leave colorful handprints on the future covering of the house. Your child will be delighted with the hut assembled and decorated with his participation.

Any person involved in construction knows that sometimes you want to build something “for the soul.” Although not entirely practical, it is pleasing to the eye. This desire is especially strong if the site is located in a picturesque place, in a forest or on a hill that offers a wonderful view of the surrounding area.

It is for such cases, when it seems that a standard house simply will not fit into the landscape, the so-called. A-frame house, or, what is more familiar to us, a hut house.

In this article we will cover:

How to build a hut house yourself.
Is it possible to improve the design of the hut house?

DIY hut house

The design of houses in the shape of the letter “A” is known in many countries. In the vastness of the USSR, triangular country houses called huts or tents.

IN North America they are known as A-frame houses. Such houses in the form of a hut were built when it was necessary to quickly and inexpensively build a house from what was “underfoot.”

A-houses are experiencing a real renaissance, and thanks to the use of modern building materials, projects of the most unusual design appear.

The house shown above is difficult to replicate on your own, therefore, speaking about how to build a hut house, we will talk about more budget ones, but no less interesting options that you can build with your own hands. Good example why a developer chooses a hut house - the history of the construction of a portal user with a nickname eglis.

eglis FORUMHOUSE Member

I have a plot of 5 acres near the city. The site offers a wonderful view of the Taganrog Bay. The place is very beautiful, you can breathe easily, you can smell the sea. An old brick house was sold along with the plot. It has no foundation, so cracks have formed in the walls. At first I wanted to finish this house: expand it, insulate it, etc., but after calculating everything, I came to the conclusion that building a new one would be cheaper. Because I will build it alone, without helpers, I needed feasible and inexpensive technology. Therefore, the choice fell on a frame hut house.

Before we talk about the stages of this construction, we will list the main pros and cons of A-houses.

Pros and cons of A-houses

The main advantage of a hut house is the saving of building materials, time and effort. In fact, the “legs” of this wigwam are both wall posts and roof rafters.

Accordingly, there is no need to build a classic “box”, on which the rafter system is then mounted.

We also note the light weight of the frame of this beautiful hut, which leads to a reduction in the material consumption of the foundation and a simplification of its design. There is no need to build a serious foundation for the building; you can get by.

Among the main disadvantages of a hut house: smaller usable area, with an equal building footprint, with a house built using classical technology. Therefore, the second floor of the “triangle” is most often used to accommodate bedrooms or an “attic” where various things can be stored.

When building a staircase in a hut house, you will have to rack your brains about how to position it and how to make it comfortable. But all the shortcomings fade into the background if you approach the matter with invention and imagination. If you make a hut house not as it goes, but by adhering to a clearly developed project, you get a truly unusual and beautiful structure that fits organically into nature.

This is what you should end up with eglis.

Work on the construction of a hut house began with the construction of a cellar.

eglis

I live in an apartment, so the urgent question is where to store pickles and jam. I decided to build a cellar right under the house.

To do this, the user independently dug a hole with a shovel measuring 1800x3500 mm and 2800 mm deep.

Having dug a pit, eglis I leveled the base with concrete, which simplified the laying of blocks.

The ceiling of the cellar is made of asbestos-cement pipes with a diameter of 11 cm.

The “50” corner was used for the manhole, which in the middle rests on the “beam” of the ceiling, made from the “12th” channel.

The user also ensured ventilation of the cellar by installing “gray” sewer pipes.

The ceiling was covered with clay on top, spilled with water and the 80 cm thick “screed” was allowed to dry under the hot southern sun.

Now it's time to build the A-frame. First of all, the user built columnar foundation. The technology is classic - a hole is dug, then it is filled with crushed stone and sand. All this is spilled with water and thoroughly compacted. Then it is placed on the prepared base concrete block, sand-cement, etc.

To prevent crushed stone and sand from becoming mixed with the soil and sinking into it over time, the base must be separated from the soil with geotextiles, which are placed in advance at the bottom of the hole.

Columnar foundation eglis consists of twelve concrete blocks measuring 30x30x30 cm. Waterproofing is laid on the blocks, on which the frame frame is laid - a beam with a cross-section of 15x10 cm.

Since, according to the user, the height of the blocks was not enough to raise the frame higher above the ground, spacers were placed between the timber and the blocks - cuttings from larch.

eglis

Having finished the foundation, I moved on to building the frame. The dimensions of the triangles of the hut house are as follows: base 5400 mm, side – 6130 mm. The distance between the triangles is 59 cm, taking into account the laying of insulation against each other, the width of which is 60 cm. A board with a section of 15x5 cm was used for the “legs”. I raised the triangle myself, using temporary stops for this - three boards. I’ll say right away that it’s physically difficult to do this alone, and considering that several times the triangles were torn off the support boards during lifting, it’s dangerous. But everything worked out, and I raised the frame.

To strengthen the frame, the triangles were additionally reinforced with construction brackets.

1. Installation of a moisture-and-windproof membrane and sheathing under the final roofing covering - corrugated slate.

The peculiarity of the membrane is that the film releases water vapor coming from the room to the outside, but does not allow wind and atmospheric moisture to enter the insulation.

2. Laying insulation - stone wool 5 cm thick, in two layers. Because “legs” are made of 15x5 cm boards, and the total thickness of the thermal insulation layer is 10 cm, it turned out to be double ventilation gap. Those. the distance between the insulation and the membrane is 5 cm, and due to the bars a second ventilation duct, between slate and film.

3. The floor insulation was carried out according to a similar scheme, with the only difference being that a galvanized mesh with a mesh size of 5x5 cm is additionally fixed between the joists.

4. Leaf wave slate was divided into 3 parts. According to the user, this makes the roof look more original. It is easier to climb the lathing with a piece weighing 7 kg than to try to fix a whole sheet.

The sheets are pre-cut to reduce the joint “hump”. The sheets were fastened with slate nails. Holes in the slate with a slightly larger diameter than the “body” of the nail were pre-drilled with a screwdriver.

5. Installation of pediments from OSB sheets. Installation of temporary stairs and doors.

6. Installation of windows.

To bend a ridge element from a galvanized sheet, the user made a sheet bender from several boards and hinges. The design of the device, available for independent repetition, is clearly demonstrated by the following photographs.

In the future, it is planned to improve the sheet bending machine and install metal guides and clamps.

7. A 2.8 cm thick tongue and groove board was used for the flooring.

Before laying, the boards were treated with fire protection. The boards were fastened into the groove with a 5 cm long self-tapping screw, which was screwed in at an angle.

The floor of the second floor is OSB 18 mm thick.

eglis

In the future I want to cover the floor with waterproof varnish. The pipe coming from the cellar will go up and sideways through a frame extension that I will build on the site of the old brick house after it is dismantled. In the extension (I will not insulate it) I will place a shower room and a shed for storing garden tools.

The user's hut house is still under construction, but it is already clear that the result is a cozy “dacha” structure that fits well into the site.

In the future, the outside walls will be covered with siding, and the base will be closed. basement siding or corrugated sheets.

How to improve the design A-frame house and build a beautiful one hut house

If the house eglis still being completed, then A-frame housesergiolakky has already been completed: a beautiful and cozy turnkey hut house is waiting for guests to take a virtual tour.

sergiolakky User FORUMHOUSE

My plot of 18 acres is located on the banks of the Volga. It offers a magnificent view of the river and the area. I decided to build a “dacha”, but with all the amenities. We supplied electricity, gas, and drilled a well for water. The question arose of what to build. I didn’t want to put an ordinary box in such a place or build something complicated: it’s both expensive and doesn’t fit into the landscape. Stopped at A-house. Although there is not much space on the second floor with this design, I actually don’t need it. Everything you need is located on the first floor.

Now let’s show a photo that inspired the user to build his own “hut”.

It is worth noting that the house shown above is the same as the cottage sergiolakky, not classic A-frame houses. Pay attention to the right side of the picture. Part of the “legs” of the supports are cut off, and the rafters rest on the extension.

Such asymmetry, on the one hand, gives the house a “zest”, and on the other, significantly expands its functionality by adding additional space.

Thanks to the fracture of the roof, it was possible to place a vestibule, a toilet, and build a dressing room underneath. The house also has a bedroom, a bathhouse with a relaxation room and a veranda.

All children love nooks and crannies. Only in solitude can you give free rein to your imagination and go on an exciting journey through imaginary worlds. That is why children often build homemade houses from pillows, blankets and other improvised materials. But if you want your child to feel like a brave traveler or the hero of his favorite fairy tale, give him a hut. Moreover, making a hut for children with your own hands is quite easy, but the child will be able to fill his leisure time with exciting games. Today “Dream House” will share with its readers ideas for building children’s huts that can be installed both in the children’s room and outside.

Making a hut for children yourself - some interesting ideas

1. Sheet and rope

To make a hut, just stretch a rope between the trees, throw a sheet over it and secure its edges with wooden pegs or other suitable means. To make the child comfortable, lay soft blankets or blankets on the ground. And even though there is nothing supernatural in such a “structure,” a child’s imagination can fill it with an exciting story. A homemade hut for children on the street will give a lot of interesting games and, moreover, will protect babies from solar overheating.

When choosing a place for a hut, give preference to darkened and level areas.

2. A hut made of gymnastic hoop and fabric

An ordinary gymnastic hoop can be an excellent basis for a children's hut. It is enough to sew a long fabric to the hoop and hang it in a horizontal position, for example, to a tree branch at such a height that the edges of the fabric reach the ground. Alternatively, you can simply throw a large piece of thick fabric over the hoop, build a cone-shaped roof and secure the frame at a convenient level. Then, to hang the hut you only need a reliable strap or ribbon.

3. Hut made of branches

Probably every child dreams of traveling around the world, dangerous adventures and exciting journeys. Help your child achieve it cherished dream possible without going beyond your own summer cottage. Since brave travelers prefer to sleep not in a warm bed, but in a hut made of tree branches, made with their own hands, the baby will certainly be delighted with such a gift.

But how to make a children's hut from branches? There are several interesting options:

Firstly, you can build a hut from flexible and long branches left after pruning trees and. To begin, collect as many branches as possible and select the largest specimens. At the site of the future hut, draw a circle and dig branches around its circumference, tilting them so that they create a cone-shaped frame. Install only two branches at a fairly wide distance from each other, because they will serve as the entrance to the future hut. Make sure the branches are firmly installed and supplement them with remaining material. It’s okay if the walls of the hut are “transparent” - being in such a house, the baby will still feel like, at least, Robinson Crusoe.
Secondly, you can make a “living” hut by decorating it with foliage and plants. If you are not in a hurry to build a miracle house, plant climbing plants around the perimeter of the frame, for example, grapes, bindweed, etc., which, as they grow, will beautifully entwine the walls of the hut. If you want to give your child a holiday “here and now,” simply cover the frame of the hut with branches and greenery.

4. Wigwam hut in the nursery and outside

A wigwam hut is a traditional Indian home. This structure has a cone shape and a strong structure. Previously, the Indians built their homes using thick branches, which were then covered with thick canvas fabric. We can also make a children's hut based on the wigwam principle. To do this, you need to select 5-7 flexible but strong twigs, and then install them in the shape of a polyhedron or semicircle. The tops of the twigs should be connected in such a way that they fit together like flowers in a bouquet, overlapping each other. At the junction, the twigs must be secured with a strong rope or a piece of fabric.

If you are installing your teepee outside, dig the bases of the twigs into the ground a little. If the wigwam will be located indoors, tie transverse rods at the bottom of the structure that will secure the structure.

After this, decorate the wigwam with fabric. Most often, triangles are formed between the nearby twigs of the hut, so you just need to cut out pieces of fabric in this shape and sew them around the frame. However, it is much more beautiful if the wigwam hut is decorated with a specially sewn cover, to create which you will need to carefully measure the height of the frame and the width of each part.

5. Gable hut

Having done simple design from several wooden slats, you can create a beautiful gable hut or hut-tent. The most important thing in this structure is to choose the right fabric. If you are setting up a hut in the yard, it is best to use tent fabric that will not fade from the sun or become deformed due to high humidity. If the structure is located in a child’s room, cotton or any other natural material will do.

Indoor huts

If you are not confident in your abilities or simply do not want to waste time making a homemade hut, you can purchase a ready-made structure. For example, beautiful and easy-to-play huts are produced by the Swedish brand IKEA. Such structures are suitable not only for games, but also for... In addition, the branded hut will certainly become the main decoration of the children's room.

You can also use a stylized awning or a roof over a bed as a hut. This accessory will not only give your baby a world of exciting games, but will also provide him with a sound and restful sleep.