Reading time: 3 min
Scratches, delaminations, gouges, dents and blisters on plastic skis can be easily repaired. 1-2 scratches will not interfere with normal gliding, and this factor will not affect the speed of movement. It is much worse if the surface of the skis is burned or poorly cycled. Improper repair and maintenance can cause more damage to sports equipment than a couple of scratches.
To repair skis you will need:
1. Burner;
2. Epoxy resin;
3. Acute cycle;
4. Repair pencil P-tech;
5. Sandpaper.
Related articles:
1. How to choose alpine skis?
2. How to lubricate skis with notches?
3. How to determine the size of alpine skis?
How to repair plastic skis?
1. If the fastening on a plastic ski has completely come off, then the holes that appear should be dried. Fill small holes epoxy resin using toothpicks or matches to help. Screw the mount into place using a self-tapping screw, without waiting for the applied product to dry. Do not tighten the screw too tightly, as you may damage the top layer and core of the ski. The epoxy resin must dry.
2. If large holes have formed at the site of the torn fastening, then they need to be filled with glue and plugs (small metal shavings, wood chips and other similar material) inserted. When everything has hardened thoroughly, fasten the mount with a screw. If the hole is very large, then the mounting location can be shifted significantly. But even in this case, the holes should be sealed.
3. Wide and deep gouges and scratches also need to be repaired. But you should not start repairs if there is grease on the surface of the skis. Clean the damaged area thoroughly. Wipe the surface with detergent and wipe dry. Sand the scratch with medium-grit sandpaper - this will raise the pile, which will facilitate adhesion of the defective surface and the repair plastic.
4. The recess can be sealed with epoxy resin, which hardens slowly. Use the one that is suitable for metal parts, it can be processed and set well with a metalworking tool. Pass over repair area blowtorch– the fire will slightly oxidize the plastic, which will allow it to better adhere to the resin. Apply epoxy to the damaged area and leave to harden for about a day.
5. For plastic there are special R-tech repair sticks. Choose sticks that match the color of your skis. Most good guy polyethylene is contained in sticks that are used in repair shops, so it is better to give preference to them. The area will also need to be heated with a torch or hairdryer - be very careful not to accidentally burn the sliding surface.
6. Heat the candle stick with a burner. Keep the fire close to the sliding surface, as the repair candle will drip onto the scratch. When the patch hardens, you need to remove the excess with a sharp scraper, making light movements.
7. To repair the sliding surface of skis, you can buy a special gun. It pushes P-tech well into damage, providing excellent connection of materials during repairs.
8. Use fine sandpaper to treat small scratches and sand this area. Use a knife to cut off the burrs on the side surface.
Now you know how to repair plastic skis! Happy renovation!
Scratches, delaminations, gouges, dents and blisters on plastic skis can be easily repaired. 1-2 scratches will not interfere with normal gliding, and this factor will not affect the speed of movement. It is much worse if the surface of the skis is burned or poorly cycled. Improper repair and maintenance can cause more damage to sports equipment than a couple of scratches.
To repair skis you will need:
1. Burner;
2. Epoxy resin;
3. Acute cycle;
4. Repair pencil P-tech;
5. Sandpaper.
How to repair plastic skis?
1. If the fastening on a plastic ski has completely come off, then the holes that appear should be dried. Fill the small holes with epoxy resin, using toothpicks or matches to help. Screw the mount into place using a self-tapping screw, without waiting for the applied product to dry. Do not tighten the screw too tightly, as you can damage the top layer and core of the ski. The epoxy resin must dry.
2. If large holes have formed at the site of the torn fastening, then they need to be filled with glue and plugs (small metal shavings, wood chips and other similar material) inserted. When everything has hardened thoroughly, fasten the mount with a screw. If the hole is very large, then the mounting location can be shifted significantly. But even in this case, the holes should be sealed.
3. Wide and deep gouges and scratches also need to be repaired. But you should not start repairs if there is grease on the surface of the skis. Clean the damaged area thoroughly. Wipe the surface with detergent and wipe dry. Sand the scratch with medium-grit sandpaper - this will raise the pile, which will facilitate adhesion of the defective surface and the repair plastic.
4. The recess can be sealed with epoxy resin, which hardens slowly. Use the one that is suitable for metal parts; it can be easily processed and set with a metalworking tool. Run a blowtorch over the repair area - the heat will slightly oxidize the plastic, allowing it to bond better with the resin. Apply epoxy to the damaged area and leave to harden for about a day.
5. For plastic there are special R-tech repair sticks. Choose sticks that match the color of your skis. The best type of polyethylene is found in sticks that are used in repair shops, so it is better to give them preference. The area will also need to be heated with a torch or hairdryer - be very careful not to accidentally burn the sliding surface.
6. Heat the candle stick with a burner. Keep the fire close to the sliding surface, as the repair candle will drip onto the scratch. When the patch hardens, you need to remove the excess with a sharp scraper, making light movements.
7. To repair the sliding surface of skis, you can buy a special gun. It pushes P-tech well into damage, providing excellent connection of materials during repairs.
8. Use fine sandpaper to treat small scratches and sand this area. Use a knife to cut off the burrs on the side surface.
Now you know how to repair plastic skis! Happy renovation!
A broken ski is a huge problem for continuing a ski trip. However, there is always a way out, although field conditions are not the most comfortable for such repairs. Nevertheless, almost any skier with many years of “hiking” experience has such experience. Wooden skis are rarely used now, because they are the easiest to break. All experienced skiers have long switched to using semi-plastic and plastic equipment. The first ones break more often, the second ones less often. What should you do if there is a breakdown? Let's consider several options.
What materials are included in the repair kit?
What should a lover of long winter walks have to fix a broken ski:
- Electrical tape.
- Reinforced plumbing tape.
- Medical adhesive plaster.
- Self-tapping screws of different lengths. Nails are an alternative.
- Metal plates (preferably lighter titanium ones). At least two. Their width should be equal to the width of the ski. Holes are pre-drilled on the surface of the plates.
- Epoxy resin.
- Fiberglass.
Above is the optimal set list. Depending on the type of breakdown and location of repair, one or another material is used. For example, a plate is attached to the broken area and secured with bolts. Many people use epoxy resin and fiberglass only for repairs in convenient conditions home workshop.
What if the ski breaks in half?
Removed and moved forward fastening mechanism used as an emergency measure. It is acceptable in cases where the density of the crust is good or there is an excellent ski track and the rest of the route cannot be called long. The broken part of the ski is secured to the backpack. The main repairs begin at the nearest rest stop (in the workshop).
In fact, there are several technologies that allow you to continue winter skiing even after such a serious “accident”:
1. First method
- A tree is being cut down. The diameter of its barrel must correspond to the thickness of the ski.
- Slightly curved (similar to the top of a ski).
- A meter long length is sawn off from the trunk.
- This is followed by double-sided trimming of the wood until a board has a thickness of 0.25-0.3 cm. Equally important is the presence of a slight deflection.
- The binding is removed from the ski.
- This is followed by the connection of the scrap, followed by the application of the manufactured board. It is placed on top.
- The board is attached to the ski using self-tapping screws or nails. The main thing is not to do this in one straight line to avoid unnecessary cracks.
- The ends of the fasteners are bent in the direction of the ski back.
- It is permissible to resort to additional reinforcement of the broken area. In this embodiment, the amplifier function will be performed by a piece of tin. The benefit of the lack of empty tin cans Travelers do not experience this during long walks.
- The finished structure is rewound with a reinforced variation of adhesive tape. As a last resort, it is permissible to use a regular adhesive plaster. The wrapping starts at the ski back and continues towards the toe.
After the repair is completed, the fastening is installed using longer self-tapping screws than in the original version. It will be more reliable this way.
2. Second technique
Involves fastening the ski parts with an overlap. The order here is important: the lower position of the front relative to the back. That is, you don’t have to look for a tree. However, the presence of self-tapping screws and special tape cannot be ruled out.
Technique for repairing a ski sock
Breaks of ski socks occur more often than other fractures, in particular in half. Some skiers pre-reinforce their socks. Their skis are equipped with several layers of fiberglass that are glued to epoxy. Some people prefer self-production metal socks. A broken ski is “decorated” with this pre-prepared attribute. You will also need screws to secure it.
In other cases, they manage by applying a splint. Ideally, plywood is used (not too large a piece). It can be replaced with two small branches. The structure is reinforced from below with a tin strip. Everything is secured with tape.
For your information . For emergency repairs, use a plastic bottle of the appropriate size. It is put on a broken ski, warmed up over a fire, bent and secured with self-tapping screws.
Universal home method for any breakdown
A simpler gluing method is based on the use of fiberglass:
- After applying epoxy to the breaking area, both pieces of the ski are tightly connected.
- Then the upper section is covered with adhesive and fiberglass is glued onto it. One layer of material is not enough. This operation is repeated several times. The result is a patch in a multi-layered variation. In this case, each layer is coated with resin.
- Finally, the broken area is bandaged with fiberglass (from heel to toe), which is also coated with epoxy resin.
- After the final layer of epoxy, you just have to wait for the epoxy glue to dry.