All those who love making tattoos and regularly visit the tattoo artist are familiar with the tattoo machine. A professional tattoo parlor uses professional equipment. There are often cases when specialists are received at home. Then they use a homemade machine made at home.
What do you need to make a tattoo machine at home?
Making a tattoo machine yourself is quite simple and does not turn into a tedious and boring assembly process. To do this you will need the following accessories and ingredients:
- antiseptic (needed for processing)
- the ink you will use directly to apply the tattoo
- guitar string
- regular ballpoint pen
- piece of wine cork
- insulating tape
- folding knife and pliers
- a toy that is powered by an electric motor
How to make a tattoo machine
It is best to choose a helium writing instrument. This is explained by the fact that the gel is easy to squeeze out of the rod; ink is more difficult to remove.
- To make the device, you need to disassemble the handle, pulling out the rod and rinsing it thoroughly
- The cap from it must be cut by a third
- Creating homemade apparatus, use a toy powered by an electric motor. Separate its housing from the motor itself
A tattoo machine can be different, both intended for individual work and reminiscent of the one created in prison. In the second case, it will be possible to work with it only in company with someone, and not alone, because this design allows one to directly type in the picture, and the other to press the buttons on the control panel.
- Secure the cap and motor with electrical tape
- The body of the handle should also be cut to about a third of its length.
- Then insert this part of the body into the cap, and then the rod into it
- Next, take a piece of the wine cork and place it on the motor.
- Cut the string to almost the length of the rod, add 1.5 cm
- Insert the string into the rod and bend the edge, inserting it into the cork
- Try to connect it closer to the shaft axis. And this is important, since it directly affects the vibration of the needle, and therefore the quality of the drawing (its accuracy, clarity, and so on)
What to remember?
It is important to know in advance how to use the device correctly. For example, before each use it is necessary to sterilize the needle. This can be done with alcohol and a lighter.
This article tells how to make a simple tattoo machine with your own hands. There are quite a lot of similar articles on the Internet, but this one is even too detailed. The most important thing is that it describes all the problems that I encountered in the process (and there were many of them).
Lyrics
In this brainstorming article I raise the topic of the ancient art of tattooing. Our friends, fathers and grandfathers beat their first army “partakis” in this artisanal way. For those who think that a tattoo made in such conditions is unsanitary and unsightly, I advise you to take a look. here (Yes, you are right, there are connoisseurs of this style of tattoos, which I am).
To all those who want to repeat:
Let's look at everything in order: 1. The motor may not necessarily be 9V, but this is the most best option. The motor can be bought on the radio market; for example, I got it from an old tape recorder.
2. The pen is the most important element our machine, it must meet certain requirements. I have tried many types of pens for... creating a rotary tattoo machine and finally found the best option. The pen must be capillary, now a little more detail...
This is what a capillary pen looks like, as you noticed, it has a metal tip through which the string fits perfectly, which means this is what we need! The price of such a “tool” is not as high as you might think; for example, I bought such a pen for 32 rubles.
We take any 9 volt 1 ampere power supply (you can use a transformer from a game console like SEGA or similar) and a nail. We connect the transformer to the socket and wind the plus from the transformer onto a string, and the minus onto a nail. Then we place the nail and the string in the water, but make sure that they do not touch each other. We do not immerse the string completely in water, but only 2 - 3 millimeters. Subsequently chemical reaction the metal strings will break down and become sharper. The reaction must be continued for 15 minutes, then the string must be washed and in the end we get the sharpest stake for a tattoo machine.
You can use a regular Bic ballpoint pen. Blow the paste out of the rod, remove the ball and, if necessary, widen the hole a little so that the needle can pass through it freely.
Bracket
Before the application procedure itself, it is best to clean the area of skin where the tattoo will be located with a scrub a day or two before. This will cleanse the skin and keep your design visible for quite a long time. Experienced craftsmen also recommend removing hair from the surface of the skin, this will help make the drawing more neat and even.
How to make a tattoo at home?
may take quite a long time. Therefore, it will be better if you leave a few hours in reserve. henna tattoos at home The application process itself
Elastic gasket
Contact screw
What about paint?
Regarding preparing tattoo paint at home, it should be noted that it is better not to prepare it yourself. You can also fork out for a special mascara. This will be safer than using pen gel or brilliant green. You understand that such materials are not very good for such an event.
It doesn't matter which paint you ultimately choose. You should immerse the tip of the needle of the machine on for about ten seconds, and then inject it under the skin. This principle is used throughout the entire work process.
Connect the power supply.
You can use any charger that is rated for a voltage no lower than the electric motor you are using. For greater convenience, you can install a switch or button.
After you are done with the tattoo machine, throw away the needle and tube (pencil or pen).
If you neglect these instructions, you risk introducing infection into the wounds, and you won’t get a beautiful tattoo. The skin must also be treated with special antiseptics before applying paint.
What other options are there?
- First you need to assemble the handle. Insert the handle shaft into the shell (base).
- Now you need to take the motor, attach it to the curved metal plate, and then use electrical tape to secure the plate tightly to the handle shaft.
- Then you need to take a piece of cork in the form of a circle, combine it with the mini-motor (put it directly on the shaft).
- You need to attach a prepared string to the motor. The string must be placed in the shaft of the handle and then attached to the motor. The free end of the string must be bent and then inserted into the plug on the shaft. For your tattoo machine to work perfectly, you need the string to come out of the rod no more than 1.5-2 mm. Therefore, you need to get rid of the excess part of the string.
- The device will be ready to use as soon as you wrap the motor with electrical tape. It is best to make several layers of winding for safety.
- You can see how to make a tattoo machine in the video, which is located just below on the page. It shows in detail and clearly how to make a tattoo machine yourself.
- Now you know how to make a tattoo machine at home. If you want a larger tattoo machine, you should choose a larger motor. Before using the machine for its intended purpose, you need to thoroughly disinfect it with alcohol and then an antiseptic. After disinfection, turn on the machine, dip it in special ink and you can start creating your masterpieces.
- Did you know
- How old are these young people?
- What could be the reason for severe regurgitation?
- A 2-year-old child has dehydration
HOW TO MAKE A TATTOO MACHINE
We make a tattoo machine with our own hands. The very concept of tattoos was formulated back in the 20s of the 20th century. Today, people ink anything on their body and pay a lot of money for it, but not many people know that the tattoo itself was born in the zones 100 years ago. And today we will look at a device that will allow you to make tattoos in a professional manner. To create such a device you only need a couple of little things - a gel pen, a guitar string, a motor from a DVD player drive or from toy car and charger from mobile phone.
We take the paste out of the gel pen and remove the tip of the paste, where the ball is. Next, take the needle and insert the needle from the back of the tip and press until the ball falls out. Then we take the paste and blow it into the washbasin until all the gel comes out of it. Now it's time to make the stake. To do this, take a guitar string and remove the spiral from it in advance. we need a piece of string with a length of 20 centimeters. Next you need to sharpen one end of the string and for this we prepare an electrolyte. Take a coffee glass and pour water into it, then you need to pour two teaspoons of table salt into the water and mix the solution.
We take any 9 volt 1 ampere power supply (you can use a transformer from a game console like SEGA or similar) and a nail. We connect the transformer to the socket and wind the plus from the transformer onto a string, and the minus onto a nail. Then we place the nail and the string in the water, but make sure that they do not touch each other. We do not immerse the string completely in water, but only 2 - 3 millimeters. As a result of the chemical reaction, the metal of the string will deteriorate and become sharper. The reaction must be continued for 15 minutes, then the string must be washed and in the end we get the sharpest stake for a tattoo machine.
After all this, we take the head for the belt drive and insert it into the motor shaft (the head can be found in any cassette recorder, it is put on the motor shaft in the mechanism), you can also use a gear, like mine. We take an ordinary needle and go to gas stove. We heat the needle and make one hole on the head, which we previously inserted onto the motor axis.
The hole should be made 1-2 millimeters from the center. Take moment glue and attach the motor to the body of the gel pen. After the glue has dried, you need to seal the fastening area with silicone, and then wrap it with tape for durability. Then the sharpened tip of the string must be passed through the hole where we previously had a ball, the string must be in the paste, and its second end must be bent in the form of a hook and stuck into the hole that we made with a needle on the head of the motor.
Now we assemble the handle, connect the mobile phone charger to the motor and everything is ready. Tattoos are made with black gel from the same gel pen. To prepare, take several gel pens, take out the paste and tip, take the vodka stopper and gently and slowly blow into the paste. Subsequently, the gel will end up in the plug. Then we turn on the machine and within 10 seconds immerse the sharpened tip into the plug with the gel. Then we take it out and make a tattoo, and so on until the end of the tattoo.
The device has been tried many times and with its help you can make tattoos no worse than on a factory tattoo machine created only for such purposes. Be careful, as tattooing is one of the ways of transmitting infection! Before each tattoo, you need to wash the tip of the device with alcohol.
To get an original tattoo on your body, you don’t have to buy a tattoo machine or go to a tattoo artist for a lot of money. You can make a device such as a tattoo machine with your own hands.
You need
- Motor holder and power supply (you can use a metal pen clip as a holder).
- Gel pen.
- Guitar string (the thinnest).
- Wire.
- Motor with a plastic roller (you can take it from the player).
Instructions
- Unscrew the gel pen and remove the paint from it. Using a needle, “pick out” the ball from the metal rod. Use a file to file the tip so that the string fits in and can move freely back and forth.
- Shorten the handle tube in half for ease of use and save string. Cut off the tube that contained the paint, leaving a piece the same size as the floor of the previous tube. This is done to limit the vibration of the string during operation.
- To attach a motor to the tube, you need to take a metal holder from the handle and attach it to the motor with a sketch. Using a hot needle the size of the string, make a small hole in the motor roller (just do it off-center).
- Measure the required string length. Using pliers, pull it tight, and then use a lighter to heat it in the place where the future sharp tip should be. When it starts to heat up, it will become thinner and burst. Use a knife sharpening stone to sharpen the string. Insert the string so that the point protrudes 4 millimeters from the rod, and bend the other end of the string into an L shape and insert it into the hole of the roller. Twist the wires with the micromotor wires and connect to the power supply.
At home, you can make a tattoo machine yourself, if you have all the necessary components, in 15-25 minutes. Before you start working with it, you should adjust it so that the string is tensioned and does not hit anywhere. You should also take a power supply with power regulation in order to increase or decrease the speed of the tool.
Do you dream of becoming a famous tattoo artist, but don’t know where to start and where to get the necessary equipment, which, moreover, costs a lot of money? There is no need to be sad about this because there is enough affordable way How to make a tattoo machine with your own hands. This will be a rotary type device. To make it, you will need the following simple “spare parts”: a power supply with variable voltage, the thinnest guitar string, a motor from an old cassette recorder or player with a couple of wires, a gear from the same, a small bushing, an ordinary gel pen, a piece of plastic tube.
So, doing it yourself assumes, first of all, the presence of a body. Actually, this is what you will hold in your hand when getting a tattoo. Let's start by making it. To do this, take the handle, remove the rod from it (we don’t throw it away, it’s needed) and trim it from the back by about a third. You can use a knife to make a small hole (about 5mm) in the side of the pen nose to make it easier to pick up mascara. Use a small file to clean the edges of the hole so that small sawdust does not get into the wound.
The next step on how to make a tattoo machine is to make a guide needle. It is made from the shaft of the same pen. It also needs to be cut to body length and paint removed. Next, remove the spout from the rod, take a needle and use it to squeeze out the ball from the inside. This is necessary so that the string can move. If the spout is too narrow, it needs to be widened by grinding off the tip with a file: the string should not get stuck anywhere or cling to anything. After all the parts are ready, we insert the nose of the rod into its rightful place, and the rod itself into the handle. The body is ready.
Continuing the topic of how to make a tattoo machine, let’s make a needle from a guitar string. Its length should be calculated so that the tip with which the tattoo will be tattooed always sticks out of the pen in any position. When the string is pulled back, that is, inside the body, its “needle” should stick out 0.5-1 mm. In the “front position” 1.5-2 mm is enough. You will need to make a loop at the opposite end of the string. Therefore, in order not to make mistakes in the calculations, insert the string into the rod, which, in turn, place into the body of the handle. And so that the string is even, does not bend or curl, it can be pre-tensioned and well calcined over a fire.
At this stage, we leave everything as is and proceed to the next step. a typewriter? Next we need to attach the motor. To do this, take a piece of a pre-prepared plastic tube (it will serve as a motor holder) and cut it lengthwise into two parts. After this, we take each half in turn and cut off a longitudinal piece several centimeters long from it. Determine the length by eye, because this cut section, when bent, should cover the motor by about a third. Each trimmed part, carefully heated over the fire, is bent and rounded. We insert the motor into these rounded halves (its wiring should go out). A handle is inserted into the groove formed below the motor from the cut tube (the untouched part). All this beauty is tightly wrapped with electrical tape or tightened with clamps. Next, we put a gear on the motor pin, which will serve as a kind of crankshaft that moves the needle back and forth. It should fit very tightly and not scroll. Next, take the bushing: a string loop will be put on it, which should also fit tightly enough. We fuse the bushing into the plastic gear, closer to the center, but so that when scrolling, the needle does not fully enter the handle in any case.
The final stage of getting the machine will be connecting the motor wiring to the power supply wiring. We try to connect it to an outlet. It should work.