Thermal detector IP 101 1a a3 connection

Peculiarities:
Electronic circuit management.
The detector periodically measures the temperature environment and when the temperature threshold is reached, it generates an alarm by closing the alarm loop.
To make it easier to monitor the detector’s operation, there is LED indicator red. In standby mode, the indicator gives short flashes at intervals of 8 s. In alarm mode, the indicator lights up constantly, which makes it possible to easily detect a triggered detector.
The detector receives power directly through the alarm loop, eliminating the need for additional power line wires.

The maximum thermal fire detector IP101-1A complies with the requirements of NPB 76-98 and is designed to output a signal to the loop fire alarm(SHPS) by closing the loop when the ambient temperature reaches a threshold value.

The detector is designed for continuous round-the-clock operation in closed heated rooms.

The detector is designed to work together with control and control devices (PKP) that receive a signal about the closure (SPS) and have a direct or alternating current loop.

The detector is not intended for use in chemically aggressive environments.

The design of the detector is ordinary according to GOST 12997-84.
Type of climatic modification - UHL category 3.1 according to GOST 15150-69 for operation in the temperature range from 0C to + 50C and relative air humidity up to 95% at a temperature of +35C.

The nominal value of the detector response temperature is +70C. The deviation of the detector response temperature from the nominal value is no more than 5%.

The inertia of the detector response (the time of rise of the ambient temperature from +25C until the moment the detector is triggered) at a temperature rise rate of 30C/min is within 39...162 seconds. The response time of the detector at a temperature rise rate of 3C/min is within the range of 433...1120 sec.

The detector is powered via the ShPS directly from the control panel. Supply voltage range from 10 to 25 V.

Current consumption in standby mode is no more than 50 µA.

The protected surface is at least 25 sq.m. Indication of standby and alarm modes.

Electronic control circuit. The detector periodically measures the ambient temperature and generates an alarm when a threshold temperature value is reached.
For easy monitoring of the detector operation, there is a red LED indicator.
In standby mode, the indicator gives short flashes at intervals of 8 s. In alarm mode, the indicator lights up constantly, which makes it possible to easily detect a triggered detector. The detector receives power directly through the alarm loop, eliminating the need for additional power line wires.
The design of the detector ensures its connection to the alarm loop without observing polarity.
The aesthetic design of the detector housing fits into the interior of any room.

Description Siberian Arsenal IP-101-1A-A3

Siberian Arsenal IP-101-1A-A3 is a fire thermal maximum detector, which is used to detect signs of fire (increase in ambient temperature). An alarm is generated when the ambient temperature reaches a threshold value.

The detectors are designed for round-the-clock operation in closed heated rooms and are designed to work together with control and control devices with direct or alternating current loops.

The detector has a microprocessor analysis of the temperature sensor signal, periodically measures the ambient temperature and, when a threshold temperature value is reached, generates an alarm by increasing the current consumption. For easy control of operation there is a red LED indicator. In standby mode, the indicator gives short flashes at intervals of 6...8 s. In alarm mode, the LED indicator in IP101-1A-A3 detectors gives double and triple flashes, respectively, with a frequency of 1 Hz. This makes it easy to detect a triggered detector. Devices of this type receive power directly through the alarm loop, eliminating the need for additional power line wires. Possibility of connecting detectors to an alarm loop without observing polarity, as well as connecting fire alarm control and control devices “Granit”, “Karat”, “UTS-1-1A”, “Kvarts” to fire loops without using external limiting resistors.

The aesthetic design of the detector housing fits into the interior of any room.

Technical characteristics Siberian Arsenal IP-101-1A-A3

• Unit: 1 piece
• Dimensions (mm): 62x62x34
• Weight (kg): 0.02
• The polarity of the supply voltage is arbitrary
• Rated operating temperature +64...+76 °С
• Response time when temperature rises at a rate of 3 °C/min* 770 ±190 s
• Interval between temperature measurements 6...8 s
• Time to return to standby mode after removing the supply voltage, at least 2 s
• Loop supply voltage 10...25 V
• Permissible loop closure current in alarm mode, no more than 20 mA
• Current consumption in standby mode, no more than 85 µA
• Residual voltage in “Fire” mode (internal), no more than 8.5 V
• Shell protection degree IP30
• Operating temperature range -10...+76 °C
• Mean time between failures 70,000 hours
• Service life: at least 10 years

Thermal detector 54°C, with indicator

Purpose

The fire thermal maximum detector "IP101-1A-A1" is used to detect signs of fire (increased ambient temperature). An alarm is generated when the ambient temperature reaches a threshold value.

The detectors are designed for round-the-clock operation in closed heated rooms and are designed to work together with control and control devices with direct or alternating current loops.

Peculiarities

• Microprocessor analysis of temperature sensor signal
• The detector periodically measures the ambient temperature and, when a threshold temperature value is reached, generates an alarm by increasing the current consumption.
• For easy control of operation there is a red LED indicator. In standby mode, the indicator gives short flashes at intervals of 6...8 s. In alarm mode, the LED indicator in IP101-1A-A1 detectors gives double and triple flashes, respectively, with a frequency of 1 Hz. This makes it easy to detect a tripped detector
• The detectors receive power directly through the alarm loop, eliminating the need for additional power line wires
• The design of the detectors ensures their connection to the alarm loop without observing polarity
• Possibility of connecting “Granit”, “Karat”, “Quartz” alarm and fire alarm control and control devices to fire loops without the use of external limiting resistors
• The aesthetic design of the detector housing fits into the interior of any room

Specifications

Purpose

Fire thermal maximum detector IP101-1A-A1 is used to detect signs of fire (increase in ambient temperature). An alarm is generated when the ambient temperature reaches a threshold value. The detectors are designed for round-the-clock operation in closed heated rooms and are designed to work together with control and control devices with direct or alternating current loops.

Peculiarities

• Microprocessor analysis of the temperature sensor signal.
• The detector periodically measures the ambient temperature and, when a threshold temperature value is reached, generates an alarm by increasing the current consumption.
• For easy control of operation there is a red LED indicator. In standby mode, the indicator gives short flashes at intervals of 6...8 s. In alarm mode, the LED indicator in the IP101-1A-A1 detector gives double and triple flashes, respectively, with a frequency of 1 Hz. This makes it easy to detect a tripped detector.
• The detectors receive power directly through the alarm loop, eliminating the need for additional power line wires.
• The design of the detectors ensures their connection to the alarm loop without observing polarity.
• Possibility of connecting fire alarm control and control devices “Granit”, “Karat”, UOTS-1-1A, “Kvarts” to fire loops without the use of external limiting resistors.
• The aesthetic design of the detector housing fits into the interior of any room.

Specifications

• Supply voltage polarity: arbitrary;
• Rated operating temperature: +54...+65°С;
• Response time when the temperature rises at a rate of 3 °C/min: 700 ±120 s;
• Interval between temperature measurements: 6...8 s;
• Time to return to standby mode after removing the supply voltage, not less than: 2 s;
• Loop supply voltage: 10...25 V;
• Permissible loop closure current in alarm mode, no more than: 20 mA;
• Current consumption in standby mode, no more than: 60 μA;
• Residual voltage in "Fire" mode (between terminals 1 and 2), no more than: 8.5 V;
• Shell protection degree: IP30;
• Operating temperature range: minus 10...+76 °C.

Characteristics of Sibirsky Arsenal IP 101-1A-A1